Magic Motorsport Flex Supports VAG MD1CS014 ECU

 

Another VAG powerhouse joins the No RFT family.

Magic Motorsport Flex version 8.4.0.0 introduces support to VAG Bosch MD1CS014 TC299 control units, that can now be managed directly inside your workshop through the Boot Glitch mode. No shipping, no RFT service.

Boot Glitch mode allows you to unlock and program independently, reducing working time and leaving you full control over the operations.

No shipping. No Remote Force Team. Just Flex.

Using Boot Glitch Mode, you gain complete control over the entire operation — from unlock to programming — while reducing turnaround times and keeping every job in-house.

  • Bosch MD1CS014 TC299 support
  • Boot Glitch Unlock
  • Bench Programming

Faster workflow and total autonomy
Available now for Flex Full Master (FLS0.5M) and Flex Full Slave (FLS0.5S) users.
One more ECU. One less reason to ship.

Key Insights:

  • Working Mode: Boot Glitch — Bench
  • Memories: Read/Write/Checksum Internal Flash, Read/Write Internal EEPROM, Full Backup, Boot Unlock
  • License: FLS0.5M/S
  • Connect/Glitch Time : From 10 seconds to 25 minutes (variable)
  • Reading Time : ~ 2 minutes and 30 seconds
  • Writing Time : ~ 2 minutes

Some of supported vehicles:

  • Volkswagen Touareg (III) CR 3.0L V6 TDI 282HP (2021MY)
  • Audi S7 (II) C8 3.0L V6 TDI MHEV 339HP (2021MY)
  • Audi SQ5 (II) FY 3.0L V6 TDI MHEV 336HP (2021MY)
  • Audi Q8 (I) 4M 3.0L V6 50TDI MHEV 282HP (2021MY)

Flex Update VAG MD1CS014 Boot Glitch Unlocking

Comments

Post a Comment

Popular posts from this blog

Foxflash Pinout to Mercedes SIEMENS VDO MSM2.0

Image
  Foxflash programmer will read and write Mercedes Benz gasoline SIEMENS VDO MSM2.0 ECU on bench. Here is the fox flash pinout to MSM 2.0. Select driver Mercedes Siemens ECUS 1.4/1.6 Siemends VDO MSM 2.0 FULL SYSTEM If old and new ecu have read flash and eeprom without problem. Write not work with foxflash. Have error. Cannot write any file as shown image below: After read flash/eprom — Disconnect ecu and restart software (unplug foxflash ) — restart Then connect again, Write flash, Also try lower power only need 13v on this ecu.
Read more

PCMTuner Chevrolet SIM2K-D160 ECU Pinout

Image
 How to read a Chevrolet SIM2K-D160 ecu with pcmtuner ? Use this in Module 30, 1,3,5 — ECU ground (just connect one of the contacts) 77 — CAN-High 78 — CAN-Low 76 — K-Line 2 — +12V (ignition on) 4 — +12V (power supply of the main relay) 6 — +12V (non-switchable power supply) You may not be able to do this ECU in BSL 53 as main processor is MPC756MXP56 Second Processor TC1738. You could try OBD Module 30 Kia/Hyundai SIM2K 2.0L, 2.5L (SIM2K-D160) But failing that, you would have to do this in BSL mode 53 http://www.pcmtuner.org/pcmtuner-module-53-infineon-tricore-bsl-operation/
Read more