Posts

Showing posts with the label PCMtuner Bench mode

PCMTuner Ford Delphi DCM6.1 Pinout

Image
 Here is the pinout for Ford Delphi DCM6.1 ECU with pcmtuner module 53 on the bench. Module 63 instruction http://www.pcmtuner.org/pcmtuner-module-53-infineon-tricore-bsl-operation/

PCMTuner BMW EDC17C50 ECU Pinout

Image
 PCMTuner ecu programmer read BMW 218 2016 F45 2.0d 110kw EDC17C50 ECU on bench module 71 successfully. Follow edc1750 pinout on pcmtuner app . Extra power supply 13.5V Also tested: Bmw f31 316d 2019 ecu edc17c50. Read ori and write mod bench mode fine read, edc17c50 bmw series 1 for stage1 all good with module 71 BMW 116d edc17c50 read/total solutions/write. performed R/W of BMW F30 EDC17C50, work done

How to Connect PCMTuner with Godiag GT105 and Jumper Cable?

Image
 Some ECU must be read through OBD connection. If you have remove these ECUs from car, you cannot directly read them on bench or boot mode. You have to read these ECUs via OBD on bench mode. How to Connect PCMTuner to Read ECU via OBD on Bench? Follow the wiring diagram below to connect pcmtuner ecu programmer with godiag gt105 breakout box and full protocol jumper cable.

PCMTuner Read Honda PGM FI Keihin SH7058 ECU via OBD on Bench

Image
 How to read Honda PGM FI Keihin SH7058 ECU PCMTuner ecu tool module 12 and Godiag Tricore Cable. Set up pcmtuner and godiag tricore cable obd bench connection Run pcmflash, go to module 12- Honda PGM-FI Keihin SH7058/1MB Identify and read ECU Keep voltage up to 12V Save data

How to Replace Transistors if PCMTuner Module 71 Bench Not Working?

Image
  PCMTuner comes with spare transistors MMBT2222A for GPT circuits, lots of people damage these by connecting wrongly to ECU so these are replacements if it happens. You can replace transistors by yourself or at the local repair shop. The error is usually caused by other power supply not pcmtuner will burn the device. If you use OBD for power supply, please do not plug in a separate 12V, otherwise, it will cause the device transistor or step-down chip to burn. MUST USE PCMtuner professional power supply! If you use your own lab power and voltage regulator. You don't know how device power works. Just adjust the voltage to 13.5 or whatever you think will cause the whole triode to burn out. How to Replace Resistors? Replace PCMTuner transistors . Make sure the device and ecu connection via bench cable is proper before changing. Select the correct protocol (ECU model) in pcmflash software when reading or writing ECU. Customer solution: Resoldered two transistors K1P,...

PCMTuner module 71 can not be used for some models?

 Here is the official list of known ECU’s that do not work /problematic in pcmtuner or pcm-flash Bench mode 71. MED17.5.5 TC1766 UDS (high TPROT for TC1766) MED17.1 TC1796 UDS (high TPROT for TC1796) EDC17CP14 TC1796 TPROT11 (high TPROT for TC1796) EDC17CP20 TC1796 TPROT10 UDS (high TPROT for TC1796) EDC17CP51 (Cummins Software) China ME17.8.8TC1728 China MED17.8.10 TC1728 For VAG group module 50 OBD can be used Some EDC17 CP ecu;s require a 10uf/50uf/100uf from ECU to GPT0 Also, dependent on Canbus gateway on vehicle, some ECU’s on the bench may require a 120Kohm resistor between CANH and CANL (pullup on bus) Module 53 known problems All Volvo sid807Evo read and write Up 2012–2013 (ford protocol) after 2013 this ecu has aa new password structure and will not work

PCMTuner Nissan Hitachi ECU Bench Pinout

Image
  Question: Hi need this Nissan Hitachi ecu pinout for pcmtuner on bench or can it work by obd? Answer: Yes either plugged into vehicle or if NATS not involved and pinout correct obd breakout on bench most nissan hitachi use this pinout