Flex Update Unlocks Bosch MDG1 ECUs via Boot Mode

 With Flex 8.1.0.0, Magic Motorsport Flex is expanding its No RFT solution with support for even more Bosch MDG1 ECUs.

More MDG1. More Freedom.

Version 8.1.0.0 of Flex Out Now

With the new Flex update, support to Boot Glitch mode introduced in the previous release expands.

Newly supported:

  • Bosch MD1CS069 TC299 — Fiat Ducato
  • Bosch MD1CS001 TC298 — BMW
  • Bosch MD1CP006 TC298 — Ford

Unlock them directly in your workshop using Boot Glitch Mode. No shipping. No Remote Force Team. Just a faster workflow and complete autonomy.
This is another step toward making the entire Bosch MDG1 TC2xx family available directly with Flex.

Thanks to the new update, you can manage more Bosch MDG1 with Aurix TC2xx microprocessor, directly in your workshop, no shipping, no RFT service.

This new support is available to all the customers with Flex Full Master (FLS0.5M) and Flex Full Slave (FLS0.5S) licenses.

Key Insights:

  • Working Mode: Boot Glitch — Bench
  • Memories: Read/Write/Checksum Internal Flash, Read/Write Internal EEPROM, Full Backup, Boot Unlock
  • License: FLS0.5M/S
  • Connect/Glitch Time : From 10 seconds to 25 minutes (variable)
  • Reading Time : ~ 2 minutes and 30 seconds
  • Writing Time : ~ 2 minutes

Some of the supported models:

  • Ford F-250 Super Duty (V) 6.7L V8 Power Stroke 474HP (2023MY)
  • Ford F-350 Super Duty (V) 6.7L V8 Power Stroke HO 500HP (2023MY)
  • Fiat Ducato (V) 2.2L MultiJet III 118HP (2021MY)
  • Fiat Ducato (V) 2.2L MultiJet III 138HP (2021MY)
  • BMW 2-Series (II) 2.0L 220d MHEV 188HP (2021MY)
  • BMW 4-Series 2.0L 420d MHEV 188HP (2020MY)

MMS Flex Update MD1CS069 MD1CS001 MD1CP006 Boot Unlocking


Comments

Post a Comment

Popular posts from this blog

Foxflash Pinout to Mercedes SIEMENS VDO MSM2.0

Image
  Foxflash programmer will read and write Mercedes Benz gasoline SIEMENS VDO MSM2.0 ECU on bench. Here is the fox flash pinout to MSM 2.0. Select driver Mercedes Siemens ECUS 1.4/1.6 Siemends VDO MSM 2.0 FULL SYSTEM If old and new ecu have read flash and eeprom without problem. Write not work with foxflash. Have error. Cannot write any file as shown image below: After read flash/eprom — Disconnect ecu and restart software (unplug foxflash ) — restart Then connect again, Write flash, Also try lower power only need 13v on this ecu.
Read more

How to Find Bosch ECU Serial Numbers and Correct Pinouts

Image
 Here is basic post for people asking basic questions, apparently now on high demand since we have gathered again new members in our ECU group . So you got bosch ecu in hand from car and how to figure out how to identify it and what pinout to use? On this case we can randomly take one bosch ecu that we will identify. So all bosch ecus start with serial numbers 028… 026. We just head to bosches page next https://www.bosch-repair-service.com/ Here you search by oe or bosch number, i have random bosch ecu here and it’s 0 281 014 544 and bosch page ends up with a result. We can see its edc16cp35. Now there are two ways. Either to search in foxflash bmw / edc16cp35 for pinout. Or we head to ecu pinout page and figure out pinout from there. One of the best online pinout catalogs can be found at ecu desing, So save webpage https://ecu.design/ecu-pinout/ Copy address and head out there. Type in edc16cp35, bmw uses two processors in this one mpc 562 and mpc564. Pinouts jus...
Read more