Flex Boot Glitch Update Supports BMW MG1CS049 MD1CS089 Unlock

 Two more Bosch ECUs are now part of the Magic Motorsport Flex Boot Glitch ecosystem.

Newly supported:

  • Bosch MG1CS049 TC298 — BMW
  • Bosch MD1CS089 TC299 — Isuzu

From high-performance BMW M models to commercial vehicles, you can now unlock and program these ECUs directly in your workshop.

  • No shipping
  • No Remote Force Team
  • Boot Glitch Unlock
  • Bench Read & Write
  • Faster jobs, complete independence

Whether you’re working on a BMW M2/M4 or an Isuzu D-Max, Flex gives you the freedom to manage the entire operation on your own.

Version 8.3.0.0 of Flex Out Now

The new Flex release further expands support to the Boot Glitch mode. As of today, you can program also BMW Bosch MG1CS049 TC298 and Isuzu Bosch MD1CS089 TC299 control units directly in your workshop, no shipping nor RFT service.

Thanks to the Boot Glitch mode, unlocking and programming can be performed independently, reducing working times and still maintaining full control over the operation.

This new support is available for customers with a Flex Full Master (FLS0.5M) or a Flex Full Slave (FLS0.5S) license.

Key insights:

  • Working Mode: Boot Glitch — Bench
  • Memories: Read/Write/Checksum Internal Flash, Read/Write Internal EEPROM, Full Backup, Boot Unlock
  • License: FLS0.5M/S
  • Connect/Glitch Time : From 10 seconds to 25 minutes (variable)
  • Reading Time : ~ 2 minutes and 30 seconds
  • Writing Time : ~ 2 minutes

Some of the supported vehicles:

  • Isuzu D-Max (III) RG 1.9L Turbo 161HP (2020MY)
  • MG Gloster (I) 2.0L TDI 161HP (2020MY)
  • BMW M2-Series (II) G87 3.0L Twin-Turbo 453HP (2023MY)
  • BMW M4-Series (II) G82 3.0L Twin-Turbo 542HP (2021MY)

Flex Boot Glitch Update BMW Isuzu MG1CS049 MD1CS089 Unlocking


Comments

Post a Comment

Popular posts from this blog

Foxflash Pinout to Mercedes SIEMENS VDO MSM2.0

Image
  Foxflash programmer will read and write Mercedes Benz gasoline SIEMENS VDO MSM2.0 ECU on bench. Here is the fox flash pinout to MSM 2.0. Select driver Mercedes Siemens ECUS 1.4/1.6 Siemends VDO MSM 2.0 FULL SYSTEM If old and new ecu have read flash and eeprom without problem. Write not work with foxflash. Have error. Cannot write any file as shown image below: After read flash/eprom — Disconnect ecu and restart software (unplug foxflash ) — restart Then connect again, Write flash, Also try lower power only need 13v on this ecu.
Read more

How to Find Bosch ECU Serial Numbers and Correct Pinouts

Image
 Here is basic post for people asking basic questions, apparently now on high demand since we have gathered again new members in our ECU group . So you got bosch ecu in hand from car and how to figure out how to identify it and what pinout to use? On this case we can randomly take one bosch ecu that we will identify. So all bosch ecus start with serial numbers 028… 026. We just head to bosches page next https://www.bosch-repair-service.com/ Here you search by oe or bosch number, i have random bosch ecu here and it’s 0 281 014 544 and bosch page ends up with a result. We can see its edc16cp35. Now there are two ways. Either to search in foxflash bmw / edc16cp35 for pinout. Or we head to ecu pinout page and figure out pinout from there. One of the best online pinout catalogs can be found at ecu desing, So save webpage https://ecu.design/ecu-pinout/ Copy address and head out there. Type in edc16cp35, bmw uses two processors in this one mpc 562 and mpc564. Pinouts jus...
Read more