Renault EMS3125 Clone: Foxflash vs OBDSTAR vs Multi Prog

 Renault Clio IV EMS3125 ECU, foxflash can do a full reading?? Can you clone? The OBD reading in the car works, but you can’t read the password, tries to be 3155. Nothing can be done on the table either, both OTB and BOOT. What other device can full read and clone this ECU?

Foxflash:

Foxflash does not have the possibility to write on this ECU only reading in OBD possible.

Xhorse Multi Prog:

No, multi prog failed to full data on EMS3125.


Foxflash vs OBDSTAR vs Xhorse Multi Prog for Renault EMS3125

OBDSTAR DC706/G3:

Yes, obdstar reads full data.

Renault Dacia EMS3125 clone ECU success.


Foxflash vs OBDSTAR vs Xhorse Multi Prog for Renault EMS3125
Foxflash vs OBDSTAR vs Xhorse Multi Prog for Renault EMS3125
Foxflash vs OBDSTAR vs Xhorse Multi Prog for Renault EMS3125

Obdstar with boot, Combiloader with boot ok. Even Flex doesn’t read it. Transdata will do the ECU work because it doesn’t need a password. And any tools with OBD Partial-read, only in a car with a synchronized immobiliser.

Comments

Post a Comment

Popular posts from this blog

Foxflash Pinout to Mercedes SIEMENS VDO MSM2.0

Image
  Foxflash programmer will read and write Mercedes Benz gasoline SIEMENS VDO MSM2.0 ECU on bench. Here is the fox flash pinout to MSM 2.0. Select driver Mercedes Siemens ECUS 1.4/1.6 Siemends VDO MSM 2.0 FULL SYSTEM If old and new ecu have read flash and eeprom without problem. Write not work with foxflash. Have error. Cannot write any file as shown image below: After read flash/eprom — Disconnect ecu and restart software (unplug foxflash ) — restart Then connect again, Write flash, Also try lower power only need 13v on this ecu.
Read more

Compare Launch X-prog3 and Autel XP400 Pro Features

Image
 The Launch X-prog3 is on the same level as the autel xp400 pro where it is more limited? in which the Autel is more powerful? Here is the clue. Launch X-Prog3 (GIII) A professional immobilizer and key programmer, often used with Launch X431 diagnostic tablets (e.g., X431 V+, Pro5, PAD VII). Specializes in ECU/TCU cloning, key programming, and immobilizer functions for a wide range of vehicles. Known for its integration with Launch’s ecosystem and built-in features like MQB AKL sync data calculation. Autel XP400 Pro An advanced key and chip programmer that works with Autel MaxiIM tablets (e.g., IM508, IM608, IM608 Pro). Excels in transponder chip reading/writing, immobilizer functions, and ECU/MCU programming. Offers standalone capabilities on PC but is most powerful when paired with Autel MaxiIM tools. Comparison Table Pros and Cons Launch X-Prog3 Pros: Excellent for ECU/TCU cloning. Built-in MQB AKL sync calculator for VW/Audi. Seamless integration wi...
Read more

PCMTuner Chevrolet SIM2K-D160 ECU Pinout

Image
 How to read a Chevrolet SIM2K-D160 ecu with pcmtuner ? Use this in Module 30, 1,3,5 — ECU ground (just connect one of the contacts) 77 — CAN-High 78 — CAN-Low 76 — K-Line 2 — +12V (ignition on) 4 — +12V (power supply of the main relay) 6 — +12V (non-switchable power supply) You may not be able to do this ECU in BSL 53 as main processor is MPC756MXP56 Second Processor TC1738. You could try OBD Module 30 Kia/Hyundai SIM2K 2.0L, 2.5L (SIM2K-D160) But failing that, you would have to do this in BSL mode 53 http://www.pcmtuner.org/pcmtuner-module-53-infineon-tricore-bsl-operation/
Read more