Foxflash Failed to Read VAG DL501 Solution: Remains at 0%

 Problem: I’m having trouble reading my DL501 gearbox at foxflash programmer. I have to disconnect and re-connect several times, but the reading remains stuck at 0% . Any solution?


Foxflash Failed to Read VAG DL501 Gearbox Solution
Foxflash Failed to Read VAG DL501 Gearbox Solution

Solution:

You need Bench MFC cable. You need to use multifunction cable that is included in foxflash kit. There is a ignition switch. 12v+ and 12v Ignition. The ignition is under the on/off switch of mfc cable. Pinout directly from device to gearbox doesn’t work.

Press read not get id.
When tool told you put on or off. After put off, CLICK read then put on After..not before.

Tested dl501 gen1 all okay. Even cloning.

If use Godiag TCU adapter, before with ECU adapter and have to press the 120ohm button briefly when building the connection then it read immediately.
Just try or plug K15 in and out.

Example:

Audi A6 C7
DL501 Cloning.
Read OK
Write OK


Foxflash Failed to Read VAG DL501 Gearbox Solution
Foxflash Failed to Read VAG DL501 Gearbox Solution
Foxflash Failed to Read VAG DL501 Gearbox Solution


Comments

Post a Comment

Popular posts from this blog

PADFlash Software Free Download for ECU TCU Programming

Image
 The PADFlash ECU TCU programmer software is now available for free download on its official website. Website address: http://www.padflashr.uk/download.html From there, you can: Check the driver list and download the PADFlash Updater Tool Manager . View the support list by vehicle brands to see which models are compatible with the software. Laptop requirement: Compatible operating systems: Windows 7 Windows 10 CPU>2.5GHz (Intel i5, i7) RAM> 4GB OS 64bit Laptop needs with USB 2.0 port and USB 3.0 port at the same time. After installing the PADFash updater tool, follow this guide to activate PADFlash software. http://www.pcmtuner.org/how-to-use-padflash-software-after-activation-on-win10/
Read more

Foxflash Pinout to Mercedes SIEMENS VDO MSM2.0

Image
  Foxflash programmer will read and write Mercedes Benz gasoline SIEMENS VDO MSM2.0 ECU on bench. Here is the fox flash pinout to MSM 2.0. Select driver Mercedes Siemens ECUS 1.4/1.6 Siemends VDO MSM 2.0 FULL SYSTEM If old and new ecu have read flash and eeprom without problem. Write not work with foxflash. Have error. Cannot write any file as shown image below: After read flash/eprom — Disconnect ecu and restart software (unplug foxflash ) — restart Then connect again, Write flash, Also try lower power only need 13v on this ecu.
Read more

Compare Launch X-prog3 and Autel XP400 Pro Features

Image
 The Launch X-prog3 is on the same level as the autel xp400 pro where it is more limited? in which the Autel is more powerful? Here is the clue. Launch X-Prog3 (GIII) A professional immobilizer and key programmer, often used with Launch X431 diagnostic tablets (e.g., X431 V+, Pro5, PAD VII). Specializes in ECU/TCU cloning, key programming, and immobilizer functions for a wide range of vehicles. Known for its integration with Launch’s ecosystem and built-in features like MQB AKL sync data calculation. Autel XP400 Pro An advanced key and chip programmer that works with Autel MaxiIM tablets (e.g., IM508, IM608, IM608 Pro). Excels in transponder chip reading/writing, immobilizer functions, and ECU/MCU programming. Offers standalone capabilities on PC but is most powerful when paired with Autel MaxiIM tools. Comparison Table Pros and Cons Launch X-Prog3 Pros: Excellent for ECU/TCU cloning. Built-in MQB AKL sync calculator for VW/Audi. Seamless integration wi...
Read more