OBDSTAR DC706 Benz VGS4 TCU Virgin Guide (Bench Mode)

OBDSTAR DC706 now will virgin Mercedes Benz FBS4 VGS4–0-NAG2 gearbox TCU on bench mode without drilling a hole.

Here comes the latest user feedback on VGS4 TCU.

"Just wanted to give you some feedback regarding a job on a Mercedes W205 that came in for a gearbox replacement. The gearbox is a VGS4–0-NAG2. I used the OBDSTAR DC706 (I renewed my subscription specifically for this job). I connected the old gearbox and was able to read it without any problems in bench mode.

Then, I successfully virginized the new gearbox without any issues (3 minutes, depending on your connection).

Next, I successfully transferred the immobilizer data and entered the VIN. The whole job took 10 minutes.

The vehicle started and is working perfectly.

I should mention that the entire process was done in bench mode with MP001."


OBDSTAR DC706 Virgin Benz W205 VGS4-0-NAG2 Gearbox on Bench
OBDSTAR DC706 Virgin Benz W205 VGS4-0-NAG2 Gearbox on Bench
OBDSTAR DC706 Virgin Benz W205 VGS4-0-NAG2 Gearbox on Bench
OBDSTAR DC706 Virgin Benz W205 VGS4-0-NAG2 Gearbox on Bench
OBDSTAR DC706 Virgin Benz W205 VGS4-0-NAG2 Gearbox on Bench
OBDSTAR DC706 Virgin Benz W205 VGS4-0-NAG2 Gearbox on Bench
OBDSTAR DC706 Virgin Benz W205 VGS4-0-NAG2 Gearbox on Bench 

Comments

Post a Comment

Popular posts from this blog

PADFlash Software Free Download for ECU TCU Programming

Image
 The PADFlash ECU TCU programmer software is now available for free download on its official website. Website address: http://www.padflashr.uk/download.html From there, you can: Check the driver list and download the PADFlash Updater Tool Manager . View the support list by vehicle brands to see which models are compatible with the software. Laptop requirement: Compatible operating systems: Windows 7 Windows 10 CPU>2.5GHz (Intel i5, i7) RAM> 4GB OS 64bit Laptop needs with USB 2.0 port and USB 3.0 port at the same time. After installing the PADFash updater tool, follow this guide to activate PADFlash software. http://www.pcmtuner.org/how-to-use-padflash-software-after-activation-on-win10/
Read more

Compare Launch X-prog3 and Autel XP400 Pro Features

Image
 The Launch X-prog3 is on the same level as the autel xp400 pro where it is more limited? in which the Autel is more powerful? Here is the clue. Launch X-Prog3 (GIII) A professional immobilizer and key programmer, often used with Launch X431 diagnostic tablets (e.g., X431 V+, Pro5, PAD VII). Specializes in ECU/TCU cloning, key programming, and immobilizer functions for a wide range of vehicles. Known for its integration with Launch’s ecosystem and built-in features like MQB AKL sync data calculation. Autel XP400 Pro An advanced key and chip programmer that works with Autel MaxiIM tablets (e.g., IM508, IM608, IM608 Pro). Excels in transponder chip reading/writing, immobilizer functions, and ECU/MCU programming. Offers standalone capabilities on PC but is most powerful when paired with Autel MaxiIM tools. Comparison Table Pros and Cons Launch X-Prog3 Pros: Excellent for ECU/TCU cloning. Built-in MQB AKL sync calculator for VW/Audi. Seamless integration wi...
Read more

Foxflash Pinout to Mercedes SIEMENS VDO MSM2.0

Image
  Foxflash programmer will read and write Mercedes Benz gasoline SIEMENS VDO MSM2.0 ECU on bench. Here is the fox flash pinout to MSM 2.0. Select driver Mercedes Siemens ECUS 1.4/1.6 Siemends VDO MSM 2.0 FULL SYSTEM If old and new ecu have read flash and eeprom without problem. Write not work with foxflash. Have error. Cannot write any file as shown image below: After read flash/eprom — Disconnect ecu and restart software (unplug foxflash ) — restart Then connect again, Write flash, Also try lower power only need 13v on this ecu.
Read more