ECM Titanium MD1CP061 Update for Ford Ranger and Amarok

 Alientech ECM Titanium released new driver update- Bosch MD1CP061 for Ford Tanger, Volkswagen Amarok and more.

Targeted control for modern high-performance diesel pickup trucks with ECM Titanium.

  • Dedicated calibration for Bosch MD1CP061 ECUs on latest-generation commercial vehicles.
  • Advanced management of EGR hysteresis, torque monitoring DTCs, speed limiters and idle speed.
  • Ideal for performance optimization, fuel efficiency and customized vehicle setups.
  • Full access to maps in table, 2D and 3D view for precise and reliable calibrations.

05.02.2026

Ford Ranger and Volkswagen Amarok are now a benchmark in the advanced work vehicle segment: robust, powerful, and increasingly used for intensive professional applications. With the latest-generation diesel engines managed by the Bosch MD1CP061 ECU, they represent an ideal platform for targeted performance and efficiency optimization.

Thanks to the ECM Titanium driver update dedicated to this control unit, you now have access to even more complete management of the main engine parameters, designed to simplify workshop operations and deliver precise, reliable calibrations.

ECUs targeted by this development

Bosch MD1CP061

Why does this update make a difference?

The new features allow advanced tuning with full control over:

  • EGR HYSTERESIS
  • DTC MANAGEMENT (TORQUE MONITORING)
  • SPEED LIMITERS
  • IDLE SPEED

EGR hysteresis: All EGR hysteresis maps are now available, enabling effective management of exhaust gas recirculation strategies.

DTC management (torque monitoring): DTCs dedicated to disabling torque monitoring are also included. A major operational advantage compared to other drivers, where interventions are usually limited to setting mg/stk maps to zero.

Speed limiters: With the new update, it is now possible to directly modify maximum speed limiters, allowing customized configurations based on vehicle use.

Idle speed: Idle speed control maps have been added, useful both for specific applications and for improving comfort and fuel efficiency.

The main structure of the new Driver

Preview the macro areas of the Driver where the update has been applied:
Bosch MD1CP061

  • Deactivations
  • Torque
  • Injection
  • Limiters (RPM, Speed)
  • Turbo
  • Rail

ECM Titanium Update MD1CP061 Driver for Ford Tanger VW Amarok

Comments

Post a Comment

Popular posts from this blog

Compare Launch X-prog3 and Autel XP400 Pro Features

Image
 The Launch X-prog3 is on the same level as the autel xp400 pro where it is more limited? in which the Autel is more powerful? Here is the clue. Launch X-Prog3 (GIII) A professional immobilizer and key programmer, often used with Launch X431 diagnostic tablets (e.g., X431 V+, Pro5, PAD VII). Specializes in ECU/TCU cloning, key programming, and immobilizer functions for a wide range of vehicles. Known for its integration with Launch’s ecosystem and built-in features like MQB AKL sync data calculation. Autel XP400 Pro An advanced key and chip programmer that works with Autel MaxiIM tablets (e.g., IM508, IM608, IM608 Pro). Excels in transponder chip reading/writing, immobilizer functions, and ECU/MCU programming. Offers standalone capabilities on PC but is most powerful when paired with Autel MaxiIM tools. Comparison Table Pros and Cons Launch X-Prog3 Pros: Excellent for ECU/TCU cloning. Built-in MQB AKL sync calculator for VW/Audi. Seamless integration wi...
Read more

Foxflash Pinout to Mercedes SIEMENS VDO MSM2.0

Image
  Foxflash programmer will read and write Mercedes Benz gasoline SIEMENS VDO MSM2.0 ECU on bench. Here is the fox flash pinout to MSM 2.0. Select driver Mercedes Siemens ECUS 1.4/1.6 Siemends VDO MSM 2.0 FULL SYSTEM If old and new ecu have read flash and eeprom without problem. Write not work with foxflash. Have error. Cannot write any file as shown image below: After read flash/eprom — Disconnect ecu and restart software (unplug foxflash ) — restart Then connect again, Write flash, Also try lower power only need 13v on this ecu.
Read more

PCMTuner Chevrolet SIM2K-D160 ECU Pinout

Image
 How to read a Chevrolet SIM2K-D160 ecu with pcmtuner ? Use this in Module 30, 1,3,5 — ECU ground (just connect one of the contacts) 77 — CAN-High 78 — CAN-Low 76 — K-Line 2 — +12V (ignition on) 4 — +12V (power supply of the main relay) 6 — +12V (non-switchable power supply) You may not be able to do this ECU in BSL 53 as main processor is MPC756MXP56 Second Processor TC1738. You could try OBD Module 30 Kia/Hyundai SIM2K 2.0L, 2.5L (SIM2K-D160) But failing that, you would have to do this in BSL mode 53 http://www.pcmtuner.org/pcmtuner-module-53-infineon-tricore-bsl-operation/
Read more