Foxflash 1.4.3.2 Update Expands Kia Hyundai ECU Coverage

 FoxFlash Manager Update to 1.4.3.2.

– Built-in HexEditor + Expanded Kia/Hyundai ECU Coverage

Kia/Hyundai/Hexedior

January 26, 2026

Built-in HexEditor + Expanded Kia/Hyundai ECU Coverage

foxFlash Official Update to Version 1.4.3.2!

Major Addition: Built-in HexEditor + Expanded Kia/Hyundai ECU Coverage

Dear foxFlash users,

We are excited to announce that foxFlash has been officially updated to version 1.4.3.2 (firmware remains fully compatible with the latest FW:D087).

Key Highlights of This Update

New Integrated HexEditor

– Professional-grade built-in hexadecimal editor now available directly inside the foxFlash software

– Makes data inspection, comparison, and modification faster and more convenient than ever:

– Open and view any read BIN file instantly

– Side-by-side comparison with original file (differences highlighted in real time)

– Easy search, replace, insert, checksum recalculation, and manual editing

– Perfect for tuning, repair, cloning, VIN changes, immobilizer work, and more

– No need to switch to third-party hex tools anymore — everything stays in one clean interface!

Expanded & Optimized ECU Support for Kia & Hyundai Models

Full coverage across OBD, Bench, Boot, JTAG, OTB modes with Mini One protocol compatibility.

Kia Carnival

– Bosch EDC17CP14 → OBD / BENCH / BOOT / OTB / Mini One

– Bosch EDC17C08 → OBD / BENCH / BOOT / OTB / Mini One

– Delphi DCM32 → OBD / OTB / Mini One

– Delphi DDCR → OBD / OTB / Mini One

Kia Carens

– Bosch EDC17CP14 → OBD / BENCH / BOOT / OTB / Mini One

– Bosch EDC16+ → BENCH / JTAG

– Bosch EDC16C39 → OBD / BENCH / JTAG / OTB / Mini One

Hyundai H1 (Starex / Travel)

– Delphi DCM3.7 → OBD / JTAG_BOOT / OTB / Mini One

– Bosch EDC15C7 → OBD / OTB / Mini One

Hyundai Getz

– Bosch EDC16C39 → OBD / BENCH / JTAG / OTB / Mini One

Hyundai Elantra / Avante / Axera / Accent series

– Bosch EDC15C7 → OBD / OTB / Mini One

– Bosch EDC16C39 → OBD / BENCH / JTAG / OTB / Mini One

– Bosch EDC17CP14 → OBD / BENCH / BOOT / OTB / Mini One

– Siemens Theta PI → JTAG

(More models and ECUs are under continuous optimization — feel free to share your real-world results!)

How to Update

– Launch foxFlash Manager — Check for Updates — Download and install 1.4.3.2 (if not work ,unstall foxFlash manager ,then install again )

– We recommend backing up your current settings before updating

– After installation, restart the software — the new HexEditor tool will appear under the "Tools" menu

– If you run into any issues, contact official support or join the foxFlash user group for instant help

Thank you all for your continued support and valuable feedback!

Your real-world usage and suggestions are what make foxFlash stronger every day.

foxFlash 1.4.3.2 is live — enjoy smoother data editing and broader Kia/Hyundai coverage!

Go update now and power through your next job with confidence.

foxFlash Team

January 2026


Foxflash V1.4.3.2 Update Kia Hyundai Hexedior


Comments

Post a Comment

Popular posts from this blog

Foxflash Pinout to Mercedes SIEMENS VDO MSM2.0

Image
  Foxflash programmer will read and write Mercedes Benz gasoline SIEMENS VDO MSM2.0 ECU on bench. Here is the fox flash pinout to MSM 2.0. Select driver Mercedes Siemens ECUS 1.4/1.6 Siemends VDO MSM 2.0 FULL SYSTEM If old and new ecu have read flash and eeprom without problem. Write not work with foxflash. Have error. Cannot write any file as shown image below: After read flash/eprom — Disconnect ecu and restart software (unplug foxflash ) — restart Then connect again, Write flash, Also try lower power only need 13v on this ecu.
Read more

PCMTuner Chevrolet SIM2K-D160 ECU Pinout

Image
 How to read a Chevrolet SIM2K-D160 ecu with pcmtuner ? Use this in Module 30, 1,3,5 — ECU ground (just connect one of the contacts) 77 — CAN-High 78 — CAN-Low 76 — K-Line 2 — +12V (ignition on) 4 — +12V (power supply of the main relay) 6 — +12V (non-switchable power supply) You may not be able to do this ECU in BSL 53 as main processor is MPC756MXP56 Second Processor TC1738. You could try OBD Module 30 Kia/Hyundai SIM2K 2.0L, 2.5L (SIM2K-D160) But failing that, you would have to do this in BSL mode 53 http://www.pcmtuner.org/pcmtuner-module-53-infineon-tricore-bsl-operation/
Read more

Compare Launch X-prog3 and Autel XP400 Pro Features

Image
 The Launch X-prog3 is on the same level as the autel xp400 pro where it is more limited? in which the Autel is more powerful? Here is the clue. Launch X-Prog3 (GIII) A professional immobilizer and key programmer, often used with Launch X431 diagnostic tablets (e.g., X431 V+, Pro5, PAD VII). Specializes in ECU/TCU cloning, key programming, and immobilizer functions for a wide range of vehicles. Known for its integration with Launch’s ecosystem and built-in features like MQB AKL sync data calculation. Autel XP400 Pro An advanced key and chip programmer that works with Autel MaxiIM tablets (e.g., IM508, IM608, IM608 Pro). Excels in transponder chip reading/writing, immobilizer functions, and ECU/MCU programming. Offers standalone capabilities on PC but is most powerful when paired with Autel MaxiIM tools. Comparison Table Pros and Cons Launch X-Prog3 Pros: Excellent for ECU/TCU cloning. Built-in MQB AKL sync calculator for VW/Audi. Seamless integration wi...
Read more