FormulaFlash 1.1.0.0 Supports Toyota Gen3 Denso ECUs

 FormulaFlash ECU programmer released new software version 1.1.0.0 in January 2026.

FormulaFlash V1.1.0.0:

UPGRADE DETAILS

NEW PROTOCOLS ADDED

Denso 3rd generation

Toyota Auris 2019–2021 DENSO GEN3
Toyota Avalon 2018–2021 DENSO GEN3
Toyota CH-R 2019–2022 DENSO GEN3
Toyota Camry 2018–2021 DENSO GEN3
Toyota Corolla 2019–2022 DENSO GEN3
Toyota Crown 2019–2022 DENSO GEN3
Toyota Harrier 2018–2022 DENSO GEN3
Toyota Highlander 2019–2022 DENSO GEN3

Toyota Hilux/Vigo (8th) 2020–2022 DENSO GEN3
Toyota Innova 2016–2020 DENSO GEN3
Toyota Kluger 2019–2022 DENSO GEN3
Toyota Land Cruiser 2020–2022 DENSO GEN3
Toyota Levin 2019–2021 DENSO GEN3
Toyota RAV4 2019–2021 DENSO GEN3
Toyota Venza 2020–2022 DENSO GEN3
Toyota Yaris 2018–2022 DENSO GEN3

Read, write and checksum correction without disassembly or external adapters.

Toyota Gen II and Gen I ECUs coming soon.

AC Delco

ACDELCO T87A (TCM), SPC564A BENCH read/write,
ACDELCO T87 (TCM), SPC564A BENCH read/write,
ACDELCO E82 BOOT mode read/write + checksum MPC5676,
ACDELCO e730/35/40/45/50 (TCM), MPC555 BENCH read/write,
ACDELCO E87 BOOT mode read/write + checksum MPC5565,
ACDELCO E92 BOOT mode read/write + checksum MPC5674,
ACDELCO E98 BOOT mode read/write + checksum MPC5674,

ECU DATA CENTER IMMO OFF MODULE

BMW Mini MSV70,
GM series, Cadillac, Buick, Chevrolet, Opel E37, E38, E67, E78,
Citroen, Peugeot ME7.4.4, ME7.4.5,
Toyota Denso 3rd generation.


FormulaFlash 1.1.0.0 Update Toyota Gen3 Denso ECUs via OBD + Bench
FormulaFlash 1.1.0.0 Update Toyota Gen3 Denso ECUs via OBD + Bench


Comments

Post a Comment

Popular posts from this blog

Foxflash Pinout to Mercedes SIEMENS VDO MSM2.0

Image
  Foxflash programmer will read and write Mercedes Benz gasoline SIEMENS VDO MSM2.0 ECU on bench. Here is the fox flash pinout to MSM 2.0. Select driver Mercedes Siemens ECUS 1.4/1.6 Siemends VDO MSM 2.0 FULL SYSTEM If old and new ecu have read flash and eeprom without problem. Write not work with foxflash. Have error. Cannot write any file as shown image below: After read flash/eprom — Disconnect ecu and restart software (unplug foxflash ) — restart Then connect again, Write flash, Also try lower power only need 13v on this ecu.
Read more

PCMTuner Chevrolet SIM2K-D160 ECU Pinout

Image
 How to read a Chevrolet SIM2K-D160 ecu with pcmtuner ? Use this in Module 30, 1,3,5 — ECU ground (just connect one of the contacts) 77 — CAN-High 78 — CAN-Low 76 — K-Line 2 — +12V (ignition on) 4 — +12V (power supply of the main relay) 6 — +12V (non-switchable power supply) You may not be able to do this ECU in BSL 53 as main processor is MPC756MXP56 Second Processor TC1738. You could try OBD Module 30 Kia/Hyundai SIM2K 2.0L, 2.5L (SIM2K-D160) But failing that, you would have to do this in BSL mode 53 http://www.pcmtuner.org/pcmtuner-module-53-infineon-tricore-bsl-operation/
Read more

Compare Launch X-prog3 and Autel XP400 Pro Features

Image
 The Launch X-prog3 is on the same level as the autel xp400 pro where it is more limited? in which the Autel is more powerful? Here is the clue. Launch X-Prog3 (GIII) A professional immobilizer and key programmer, often used with Launch X431 diagnostic tablets (e.g., X431 V+, Pro5, PAD VII). Specializes in ECU/TCU cloning, key programming, and immobilizer functions for a wide range of vehicles. Known for its integration with Launch’s ecosystem and built-in features like MQB AKL sync data calculation. Autel XP400 Pro An advanced key and chip programmer that works with Autel MaxiIM tablets (e.g., IM508, IM608, IM608 Pro). Excels in transponder chip reading/writing, immobilizer functions, and ECU/MCU programming. Offers standalone capabilities on PC but is most powerful when paired with Autel MaxiIM tools. Comparison Table Pros and Cons Launch X-Prog3 Pros: Excellent for ECU/TCU cloning. Built-in MQB AKL sync calculator for VW/Audi. Seamless integration wi...
Read more