Renault SID307 OBD Issue Fix Using Flex Boot Mode

 Alientech KESS3 released new OBD & OBD VR protocols for Marelli MM11MPHW002 ECUs- Aprilia and Moto Guzzi motorcycles.

Unlock tuning on the latest supersport and modern classic platforms from the Piaggio group with KESS3 — including the full RS and Tuono lineup and the Moto Guzzi V7 — and expand your offer across the next generation of two-wheelers.

  • Work via OBD and OBD VR
  • Read and write with complete reliability on the latest MM11MPHW002 ECUs
  • Offer tuning services from 125cc up to high-displacement engines

11.12.2025 — UPGRADE 2.70

With this update, you can work on the modern Marelli MM11MPHW002 ECUs installed on the most recent Aprilia (and Moto Guzzi) models, from 125cc to higher-displacement engines.

A major step forward for your workshop: the OBD and OBD VR connection gives you direct access to engine control unit data, allowing complete and reliable reading and writing operations.

Thanks to extended support for the entire RS and Tuono range, you can offer specialist services even on the newest platforms of the Piaggio group. A concrete opportunity to expand your offer in the motorcycle sector and stand out in the supersport and modern-classic markets.

Technical focus
Connection: OBD, OBD VR
ECU: Marelli MM11MPHW002
Production years: from 2024
Brands involved: Aprilia, Moto Guzzi

Supported vehicles
Aprilia RS 125, RS 457, RS 660, RSV4 1100, Tuono 660, Tuono 1100
Moto Guzzi V7


KESS3 Adds Motorcycle Marelli MM11MPHW002 ECUs 

Comments

Post a Comment

Popular posts from this blog

PCMTuner Chevrolet SIM2K-D160 ECU Pinout

Image
 How to read a Chevrolet SIM2K-D160 ecu with pcmtuner ? Use this in Module 30, 1,3,5 — ECU ground (just connect one of the contacts) 77 — CAN-High 78 — CAN-Low 76 — K-Line 2 — +12V (ignition on) 4 — +12V (power supply of the main relay) 6 — +12V (non-switchable power supply) You may not be able to do this ECU in BSL 53 as main processor is MPC756MXP56 Second Processor TC1738. You could try OBD Module 30 Kia/Hyundai SIM2K 2.0L, 2.5L (SIM2K-D160) But failing that, you would have to do this in BSL mode 53 http://www.pcmtuner.org/pcmtuner-module-53-infineon-tricore-bsl-operation/
Read more

Compare Launch X-prog3 and Autel XP400 Pro Features

Image
 The Launch X-prog3 is on the same level as the autel xp400 pro where it is more limited? in which the Autel is more powerful? Here is the clue. Launch X-Prog3 (GIII) A professional immobilizer and key programmer, often used with Launch X431 diagnostic tablets (e.g., X431 V+, Pro5, PAD VII). Specializes in ECU/TCU cloning, key programming, and immobilizer functions for a wide range of vehicles. Known for its integration with Launch’s ecosystem and built-in features like MQB AKL sync data calculation. Autel XP400 Pro An advanced key and chip programmer that works with Autel MaxiIM tablets (e.g., IM508, IM608, IM608 Pro). Excels in transponder chip reading/writing, immobilizer functions, and ECU/MCU programming. Offers standalone capabilities on PC but is most powerful when paired with Autel MaxiIM tools. Comparison Table Pros and Cons Launch X-Prog3 Pros: Excellent for ECU/TCU cloning. Built-in MQB AKL sync calculator for VW/Audi. Seamless integration wi...
Read more

Foxflash Pinout to Mercedes SIEMENS VDO MSM2.0

Image
  Foxflash programmer will read and write Mercedes Benz gasoline SIEMENS VDO MSM2.0 ECU on bench. Here is the fox flash pinout to MSM 2.0. Select driver Mercedes Siemens ECUS 1.4/1.6 Siemends VDO MSM 2.0 FULL SYSTEM If old and new ecu have read flash and eeprom without problem. Write not work with foxflash. Have error. Cannot write any file as shown image below: After read flash/eprom — Disconnect ecu and restart software (unplug foxflash ) — restart Then connect again, Write flash, Also try lower power only need 13v on this ecu.
Read more