FormulaFlash 1.0.9.0 Release Adds New SIM2K and E-Series ECUs

 FormulaFlash ECU TCU programmer software released to V1.0.9.0 on Dec. 18th, 2025.

READ-WRITE PROTOCOL

BYD BYD TB10 R5F72531

BOSCH BOSCH M7.9.7.1-ST10F275 ST10F275 Boot mode reading EEPROM+FLASH

Chang’an CHANGAN VISTEON STC-113-ST10F273 ST10F273

DEPHI LANDWIND DELPHI X7 MT62.1 SPC5643

GWM DELPHI MT95.1(MASTER) TC367

CHERY DELPHI E3 MT62.1 SPC5643

GAC DELPHI MT92.1 TC265

NANJUN DELPHI MT62.1 SPC5643

GAC DELPHI MT62.1 SPC5643

CHERY DELPHI MT22.3 SPC5643

GAC DELPHI MT95.1 TC367

CONTINENTAL

Continental SIM2K-240(ECM) TC1767

Continental SIM2K-241(TCM) TC1738

Continental SIM2K-241(ECM) TC1767

DECLO E78 MPC5566 BOOT reading FLASH+EEPROM

E80 MPC5676 Boot mode reading FLASH+EEPROM

DTC off

Honda 37820-XXX-XXX SH72534
Honda 37820-XXX-XXX SH72536
Honda 37820-XXX-XXX SH7058
Honda 37820-XXX-XXX MPC5566
Honda 37820-XXX-XXX TC1782

Alfa Romeo
FIAT
Fiat Doblo
JEEP
JEEP
Opel

EDC17C69
EDC17C52
EDC17C49
EDC17C49
EDC17C69
EDC17C59

— 

IDEL SPEED

ME7.8/ME7.8.8/ME7.9.7/ME7.9.7.1 Changan, Chery, MG, Hongqi, BYD, Roewe, Lynk & Co, Luxgen, Geely, Haval, Trumpchi, Wuling
MED9.6 Cadillac, Chevrolet, Buick, Opel
MG1CS002/MED9.1/MED9.1.1 Audi, Volkswagen, SEAT, Skoda
ME9.7 Mercedes-Benz MEG17.9.8 Hyundai-Kia ME17.9.1 Hyundai-Kia
ME17.9.21 Hyundai-Kia
MEDG17.9.12 Hyundai-Kia
MEDG17.9.21 Hyundai-Kia
ME17.8.8 Changan, Chery, Geely, Haval, Trumpchi, Wuling, MG, Hongqi, BYD, Roewe, Lynk & Co, Luxgen
MED17.8.10/MED17.8.2 Changan, Chery, MG, Hongqi, BYD, Roewe, Lynk & Co, Luxgen, Geely, Haval, Trumpchi, Wuling
ME17.9.6/ME17.9.0 Suzuki
ME17.3.0 Maserati, Alfa Romeo, Dodge, Fiat, Jeep, Lancia, Chrysler, Abarth"

— 

water temperature control

BMW MEV17/MEVD17
MEV17.2
MEV17.2.1
MEV17.4.2
MEVD17.2
MEVD17.2.3
MEVD17.2.4

MEVD17.2.5
MEVD17.2.8
MEVD17.2.9
MEVD17.8.4
MEVD17.2.8
MEVD17.2G


FormulaFlash 1.0.9.0 Adds SIM2K-240 SIM2K-241 E78 E80 etc ECUs


Comments

Post a Comment

Popular posts from this blog

PCMTuner Chevrolet SIM2K-D160 ECU Pinout

Image
 How to read a Chevrolet SIM2K-D160 ecu with pcmtuner ? Use this in Module 30, 1,3,5 — ECU ground (just connect one of the contacts) 77 — CAN-High 78 — CAN-Low 76 — K-Line 2 — +12V (ignition on) 4 — +12V (power supply of the main relay) 6 — +12V (non-switchable power supply) You may not be able to do this ECU in BSL 53 as main processor is MPC756MXP56 Second Processor TC1738. You could try OBD Module 30 Kia/Hyundai SIM2K 2.0L, 2.5L (SIM2K-D160) But failing that, you would have to do this in BSL mode 53 http://www.pcmtuner.org/pcmtuner-module-53-infineon-tricore-bsl-operation/
Read more

Compare Launch X-prog3 and Autel XP400 Pro Features

Image
 The Launch X-prog3 is on the same level as the autel xp400 pro where it is more limited? in which the Autel is more powerful? Here is the clue. Launch X-Prog3 (GIII) A professional immobilizer and key programmer, often used with Launch X431 diagnostic tablets (e.g., X431 V+, Pro5, PAD VII). Specializes in ECU/TCU cloning, key programming, and immobilizer functions for a wide range of vehicles. Known for its integration with Launch’s ecosystem and built-in features like MQB AKL sync data calculation. Autel XP400 Pro An advanced key and chip programmer that works with Autel MaxiIM tablets (e.g., IM508, IM608, IM608 Pro). Excels in transponder chip reading/writing, immobilizer functions, and ECU/MCU programming. Offers standalone capabilities on PC but is most powerful when paired with Autel MaxiIM tools. Comparison Table Pros and Cons Launch X-Prog3 Pros: Excellent for ECU/TCU cloning. Built-in MQB AKL sync calculator for VW/Audi. Seamless integration wi...
Read more

Foxflash Pinout to Mercedes SIEMENS VDO MSM2.0

Image
  Foxflash programmer will read and write Mercedes Benz gasoline SIEMENS VDO MSM2.0 ECU on bench. Here is the fox flash pinout to MSM 2.0. Select driver Mercedes Siemens ECUS 1.4/1.6 Siemends VDO MSM 2.0 FULL SYSTEM If old and new ecu have read flash and eeprom without problem. Write not work with foxflash. Have error. Cannot write any file as shown image below: After read flash/eprom — Disconnect ecu and restart software (unplug foxflash ) — restart Then connect again, Write flash, Also try lower power only need 13v on this ecu.
Read more