AutoTuner Update Supports KTM KTKS and KTKZ ECUs

 You seemed to love the addition of the first KTMs to AutoTuner, so we decided not to stop there!

Starting now, you can benefit from the KTM KTKS/KTKZ OBD NR protocol on your Tool.
As a reminder, NR stands for "Normal Read". This gives you access to the real content of the ECU on 14 different models from KTM, GasGas, and Husqvarna.
Share your experience with motorcycle tuning and let us know what else you need!

Key Features:
Type: Engine Control Unit (ECU).
Mode: OBD NR.
Readout: Software + Calibration.
MCU: RH850.
Read time: 10min 30sec
Write time: 6min
Checksums correction.

Compatibility List*:
GasGas Model: ES 700–2022
GasGas Engine: 700cc
Husqvarna Models: 701–2021 / 701 Supermoto — 2016 / 701 Supermoto — 2020
Husqvarna Engine: 701cc (690 platform)
KTM Models: 690 Enduro R — 2021 / 690 SMC R — 2021 / Adventure — 2009 / Super Adventure — 2015 / 1290 Super Adventure R — 2021 / 1290 Super Adventure S — 2021 / 1290 Super Duke GT — 2021 / 1290 Super Duke R — 2020 / 1290 Super Duke RR — 2020 / 1300 Brabus R — 2020
KTM Engines: 690cc / 1290cc / 1300cc
*The list of motorcycles may evolve over time.


AutoTuner Update Motorcycle KTM KTKS KTKZ ECUs via OBD NR 

Comments

Post a Comment

Popular posts from this blog

PCMTuner Chevrolet SIM2K-D160 ECU Pinout

Image
 How to read a Chevrolet SIM2K-D160 ecu with pcmtuner ? Use this in Module 30, 1,3,5 — ECU ground (just connect one of the contacts) 77 — CAN-High 78 — CAN-Low 76 — K-Line 2 — +12V (ignition on) 4 — +12V (power supply of the main relay) 6 — +12V (non-switchable power supply) You may not be able to do this ECU in BSL 53 as main processor is MPC756MXP56 Second Processor TC1738. You could try OBD Module 30 Kia/Hyundai SIM2K 2.0L, 2.5L (SIM2K-D160) But failing that, you would have to do this in BSL mode 53 http://www.pcmtuner.org/pcmtuner-module-53-infineon-tricore-bsl-operation/
Read more

Compare Launch X-prog3 and Autel XP400 Pro Features

Image
 The Launch X-prog3 is on the same level as the autel xp400 pro where it is more limited? in which the Autel is more powerful? Here is the clue. Launch X-Prog3 (GIII) A professional immobilizer and key programmer, often used with Launch X431 diagnostic tablets (e.g., X431 V+, Pro5, PAD VII). Specializes in ECU/TCU cloning, key programming, and immobilizer functions for a wide range of vehicles. Known for its integration with Launch’s ecosystem and built-in features like MQB AKL sync data calculation. Autel XP400 Pro An advanced key and chip programmer that works with Autel MaxiIM tablets (e.g., IM508, IM608, IM608 Pro). Excels in transponder chip reading/writing, immobilizer functions, and ECU/MCU programming. Offers standalone capabilities on PC but is most powerful when paired with Autel MaxiIM tools. Comparison Table Pros and Cons Launch X-Prog3 Pros: Excellent for ECU/TCU cloning. Built-in MQB AKL sync calculator for VW/Audi. Seamless integration wi...
Read more

Foxflash Pinout to Mercedes SIEMENS VDO MSM2.0

Image
  Foxflash programmer will read and write Mercedes Benz gasoline SIEMENS VDO MSM2.0 ECU on bench. Here is the fox flash pinout to MSM 2.0. Select driver Mercedes Siemens ECUS 1.4/1.6 Siemends VDO MSM 2.0 FULL SYSTEM If old and new ecu have read flash and eeprom without problem. Write not work with foxflash. Have error. Cannot write any file as shown image below: After read flash/eprom — Disconnect ecu and restart software (unplug foxflash ) — restart Then connect again, Write flash, Also try lower power only need 13v on this ecu.
Read more