New KESS3 Protocol for Iveco Daily EDC17CP52 ECUs

 Alientech KESS3 released new protocol for Bosch EDC17CP52- Iveco Daily 2.3 and 3.0 FPT.

Work in OBD, BENCH, and BOOT modes, now also with KESS3 truck and agri activation, on Iveco commercial vehicles for complete control over the most common FPT engines in Europe.
Full access for EDC17CP52 ECUs
Read, write, and clone safely and reliably
Ideal for repair, maintenance, and performance optimization.


KESS3 Update Iveco Daily SGW EDC17CP52 via OBD Bench Boot

15.10.2025 — UPGRADE 2.49

KESS3 now also supports the EDC17CP52, giving you full control over the entire 2.3 and 3.0 FPT range, available with the KESS3 Truck/Agri activation (for vehicles over 3.5 tonnes).

You can work on Daily vehicles from the 4th to the 5th generation (from 2009 onwards) using OBD, BENCH and BOOT, with the flexibility required for any type of operation:

OBD, for fast and safe operations directly via diagnostics, BENCH or BOOT, for complete access to the file and to manage vehicles that do not communicate via OBD.
A protocol that allows you to perform reading, writing and cloning operations with total reliability, reducing workshop time and increasing your daily productivity.

Technical focus
Connection: OBD/BENCH/BOOT
ECU: Bosch EDC17CP52
Production years: from 2009
Brands involved: Iveco

Supported vehicles
Iveco Daily 40C, 45C, 50C, 60C, 65C, 70C

Comments

Post a Comment

Popular posts from this blog

PCMTuner Chevrolet SIM2K-D160 ECU Pinout

Image
 How to read a Chevrolet SIM2K-D160 ecu with pcmtuner ? Use this in Module 30, 1,3,5 — ECU ground (just connect one of the contacts) 77 — CAN-High 78 — CAN-Low 76 — K-Line 2 — +12V (ignition on) 4 — +12V (power supply of the main relay) 6 — +12V (non-switchable power supply) You may not be able to do this ECU in BSL 53 as main processor is MPC756MXP56 Second Processor TC1738. You could try OBD Module 30 Kia/Hyundai SIM2K 2.0L, 2.5L (SIM2K-D160) But failing that, you would have to do this in BSL mode 53 http://www.pcmtuner.org/pcmtuner-module-53-infineon-tricore-bsl-operation/
Read more

Foxflash Pinout to Mercedes SIEMENS VDO MSM2.0

Image
  Foxflash programmer will read and write Mercedes Benz gasoline SIEMENS VDO MSM2.0 ECU on bench. Here is the fox flash pinout to MSM 2.0. Select driver Mercedes Siemens ECUS 1.4/1.6 Siemends VDO MSM 2.0 FULL SYSTEM If old and new ecu have read flash and eeprom without problem. Write not work with foxflash. Have error. Cannot write any file as shown image below: After read flash/eprom — Disconnect ecu and restart software (unplug foxflash ) — restart Then connect again, Write flash, Also try lower power only need 13v on this ecu.
Read more

Foxflash Update DCM7.24 E38 E92 E83 E0 E39A via OBD

Image
 What's the difference between Foxflash and the new KT200 II 2nd generation ecu/tcu programmer? Foxflash: free online update to get more protocols. KT200 II: it's a separate new hardware with new protocols Foxflash: more stable KT200: less stable, often bricks ECU Foxflash: reading and writing is faster and stable in the long run. Direct update foxflash online to get KT200 II protocols for example: Marelli 8GMC BENCH Delco E38 OBD BENCH E67 BENCH E84 BENCH E92 OBD BENCH SIM2K-305 BOOT Bosch MG1CA007 BENCH Delphi DCM7.24 OBD Phoenix L40 OBD EDC17C11 BENCH BOOT MD1CS069 OBD BENCH New Clone function MEDC17 FCA HYUNDAI JAGUAR LAND ROVER SUZUKI TOYOTA Transmission protocols BOSH 6L45 6L50 6L80 6L90 BENCH see http://www.pcmtuner.org/foxflash-update-dcm7-24-e38-e92-e83-e0-e39a-via-obd/ Users are allowed to update the above protocols to foxflash directly online without purchasing any new hardware or adapters. Foxflash will continue to update more ECU/TCU prot...
Read more