KESS3 Adds Full Access to Iveco Daily EDC17C49 ECU

 Alientech KESS3 released new procotol for Bosch EDC17C49- Iveco Daily 2.3 & 3.0 FPT.

Operate in OBD, BENCH, and BOOT modes on Iveco light commercial vehicles and manage the most popular FPT engines in Europe with maximum flexibility and reliability.
Full access via OBD, BENCH & BOOT.
Read, write, and clone safely and efficiently.
Ideal for maintenance, repair, and tuning operations.


Alientech KESS3 Adds Iveco Daily EDC17C49 via OBD, Bench and Boot

13.10.2025 — UPGRADE 2.48

KESS3 expands its field of action and makes interventions on the most common work vehicles in Europe even easier.
With this update you can read, write and clone in OBD, BENCH and BOOT the Bosch EDC17C49 installed on Iveco Daily 2.3 and 3.0 FPT, from the 4th to the 5th generation (from 2009 onwards).

A protocol that allows you to optimise and maintain the FPT engines most used in professional settings, with reduced processing times and maximum safety in the procedures.
Thanks to the triple connection mode, you choose how to operate:

in OBD for a quick intervention without disassembly,
in BENCH or BOOT for direct access to the ECU and full cloning.
A release designed to make your workshop even more competitive in the commercial vehicle market.

Technical focus
Connection: OBD/BENCH/BOOT
ECU: Bosch EDC17C49
Production years: from 2009
Brands involved: Iveco

Supported vehicles

Iveco Daily 40C, 45C, 50C, 60C, 65C, 70C

Comments

Post a Comment

Popular posts from this blog

PCMTuner Chevrolet SIM2K-D160 ECU Pinout

Image
 How to read a Chevrolet SIM2K-D160 ecu with pcmtuner ? Use this in Module 30, 1,3,5 — ECU ground (just connect one of the contacts) 77 — CAN-High 78 — CAN-Low 76 — K-Line 2 — +12V (ignition on) 4 — +12V (power supply of the main relay) 6 — +12V (non-switchable power supply) You may not be able to do this ECU in BSL 53 as main processor is MPC756MXP56 Second Processor TC1738. You could try OBD Module 30 Kia/Hyundai SIM2K 2.0L, 2.5L (SIM2K-D160) But failing that, you would have to do this in BSL mode 53 http://www.pcmtuner.org/pcmtuner-module-53-infineon-tricore-bsl-operation/
Read more

Foxflash Pinout to Mercedes SIEMENS VDO MSM2.0

Image
  Foxflash programmer will read and write Mercedes Benz gasoline SIEMENS VDO MSM2.0 ECU on bench. Here is the fox flash pinout to MSM 2.0. Select driver Mercedes Siemens ECUS 1.4/1.6 Siemends VDO MSM 2.0 FULL SYSTEM If old and new ecu have read flash and eeprom without problem. Write not work with foxflash. Have error. Cannot write any file as shown image below: After read flash/eprom — Disconnect ecu and restart software (unplug foxflash ) — restart Then connect again, Write flash, Also try lower power only need 13v on this ecu.
Read more

Foxflash Update DCM7.24 E38 E92 E83 E0 E39A via OBD

Image
 What's the difference between Foxflash and the new KT200 II 2nd generation ecu/tcu programmer? Foxflash: free online update to get more protocols. KT200 II: it's a separate new hardware with new protocols Foxflash: more stable KT200: less stable, often bricks ECU Foxflash: reading and writing is faster and stable in the long run. Direct update foxflash online to get KT200 II protocols for example: Marelli 8GMC BENCH Delco E38 OBD BENCH E67 BENCH E84 BENCH E92 OBD BENCH SIM2K-305 BOOT Bosch MG1CA007 BENCH Delphi DCM7.24 OBD Phoenix L40 OBD EDC17C11 BENCH BOOT MD1CS069 OBD BENCH New Clone function MEDC17 FCA HYUNDAI JAGUAR LAND ROVER SUZUKI TOYOTA Transmission protocols BOSH 6L45 6L50 6L80 6L90 BENCH see http://www.pcmtuner.org/foxflash-update-dcm7-24-e38-e92-e83-e0-e39a-via-obd/ Users are allowed to update the above protocols to foxflash directly online without purchasing any new hardware or adapters. Foxflash will continue to update more ECU/TCU prot...
Read more