CG FC200 Registration Binding and Login Tutorial

 Problem:

I had a problem logging into CG FC200 programmer. It asks to bind the device. What can I do?


How to Register, Bind and Login CG FC200

Solution:

After the 1.2.9.4 version update, if do not log in or bind the device, cannot use the software. iECUTool.eu here will tell you how to register an account and how to recover the password if you have an account but do not remember the password.

Case1:
Open 1.2.9.4 software version,and will ask you to log into an account, if you registered one before then fill information to log in directly.


How to Register, Bind and Login CG FC200

After login, click "binding device" bind the device.


How to Register, Bind and Login CG FC200
How to Register, Bind and Login CG FC200
How to Register, Bind and Login CG FC200

Case 2: Need to register a new account (never register an account before).


How to Register, Bind and Login CG FC200

Hit Register an account.


How to Register, Bind and Login CG FC200

Fill all the information according the tips.
Please note: Set the username and password as simple as possible to facilitate subsequent memory.

If the prompt says that the verification code cannot be obtained, switch the server, restart the software and try again


How to Register, Bind and Login CG FC200

Case 3: If you have registered an account before but don’t remember the password, follow the steps below.
Hit Retrieve password.


How to Register, Bind and Login CG FC200

You can retrieve password by phone number or by email.


How to Register, Bind and Login CG FC200

Verified by email address.
Fill in email address and password, then paste the verification code in email. Then submit.


How to Register, Bind and Login CG FC200

Verified by phone number.
Fill in phone number and password, then paste the verification code. Then submit.


How to Register, Bind and Login CG FC200
How to Register, Bind and Login CG FC200

Reset password successfully.

www.iecutool.eu

Comments

Post a Comment

Popular posts from this blog

Foxflash Update DCM7.24 E38 E92 E83 E0 E39A via OBD

Image
 What's the difference between Foxflash and the new KT200 II 2nd generation ecu/tcu programmer? Foxflash: free online update to get more protocols. KT200 II: it's a separate new hardware with new protocols Foxflash: more stable KT200: less stable, often bricks ECU Foxflash: reading and writing is faster and stable in the long run. Direct update foxflash online to get KT200 II protocols for example: Marelli 8GMC BENCH Delco E38 OBD BENCH E67 BENCH E84 BENCH E92 OBD BENCH SIM2K-305 BOOT Bosch MG1CA007 BENCH Delphi DCM7.24 OBD Phoenix L40 OBD EDC17C11 BENCH BOOT MD1CS069 OBD BENCH New Clone function MEDC17 FCA HYUNDAI JAGUAR LAND ROVER SUZUKI TOYOTA Transmission protocols BOSH 6L45 6L50 6L80 6L90 BENCH see http://www.pcmtuner.org/foxflash-update-dcm7-24-e38-e92-e83-e0-e39a-via-obd/ Users are allowed to update the above protocols to foxflash directly online without purchasing any new hardware or adapters. Foxflash will continue to update more ECU/TCU prot...
Read more

Foxflash, KESS3, Flex: Read Fiat Marelli 9DF ECU Easily

Image
 To read Fiat Magneti Marelli IAW 9DF ECU, you have 3 options: 1.Flex in boot mode You have to open the ecu or make a hole in the center of the inscription "Magneti" Marelli" and connect the starter through the hole With Flex you can have a vr file but it doesn’t can’t write in obd. 2. Use Kess3 , Foxflash , fgtech, autotuner for obd read and obd write (To read, you need 2 hours, to write 10/15 minutes) it makes a Reading in 2h23 For mj9dfhw001 fiat ducato using foxflash. HW001 obd Hw002 boot, 5 minutes of work with opening the computer, FoxFlash takes a long time to read and write. with kess3 OBD 1:30 reading, 15 min writing. with autotuner, he does it pretty fast but only in virtual reading and reading and writing via Obd 3. Use ktag, fgtech, dfox, in jtag by open ecu. FYI: Depends on hardware version. bench is the same 2.30 hours of reading and but sometimes impossible to write. HW000 is ok to write on bench. 0001 0002 impossible to write a mod. R...
Read more

PCMTuner Chevrolet SIM2K-D160 ECU Pinout

Image
 How to read a Chevrolet SIM2K-D160 ecu with pcmtuner ? Use this in Module 30, 1,3,5 — ECU ground (just connect one of the contacts) 77 — CAN-High 78 — CAN-Low 76 — K-Line 2 — +12V (ignition on) 4 — +12V (power supply of the main relay) 6 — +12V (non-switchable power supply) You may not be able to do this ECU in BSL 53 as main processor is MPC756MXP56 Second Processor TC1738. You could try OBD Module 30 Kia/Hyundai SIM2K 2.0L, 2.5L (SIM2K-D160) But failing that, you would have to do this in BSL mode 53 http://www.pcmtuner.org/pcmtuner-module-53-infineon-tricore-bsl-operation/
Read more