FormulaFlash Update: SIM2K SID208 SID209 Support

 FormulaFlash ECU and TCU programmer released new ECU protocols on Aug. 5th, 2025.

THE NEWLY ADDED PROTOCOL IS AS FOLLOWS

Continental Series

  • SIM2K-341 (ECM) MPC561 reads and writes flash and maps via BENCH;
  • SIM2K-141 (ECM) MPC561/2 reads and writes flash and maps via BENCH;
  • SIM2K-141 (TCM) AM29F400BB reads and writes flash via BOOT;
  • EMS2204 TC1738 reads and writes EEPROM/FLASH via BOOT;
  • EMS2211 TC1738 reads and writes EEPROM/FLASH via BOOT;
  • SID208 TC1797 reads and writes EEPROM/FLASH via BENCH & BOOT;
  • SID209 TC1797 reads and writes EEPROM/FLASH via BOOT;
  • Wuling SIM2K-D51/51.4, SCE60 Checksum

DELPHI Series

  • MT22.1.1 Beta (XEQ384 384KB) MC9S12XEQ384MAL Read/Write EEPROM/FLASH via OBD/BENCH;
  • DCM6.2AP Model Verification Function

KEFICO/BOSCH

  • MG7.9.8 ST10F275+95160 read & write EEPROM/FLASH by BOOT
  • ME7.8.8/ME7.8 Checksum

ACDELCO

  • E39/E39A MPC5566 read & write EEPROM/FLASH by BOOT

Optimization

  • Delphi DELPHI MT22 system entry and data writing CKS process

FormulaFlash Adds SIM2K-341 SIM2K141 SID208 SID209 ECUs


Comments

Post a Comment

Popular posts from this blog

PCMTuner Renault EMS3155 ECU Pinout

Image
 Question: Has someone maybe pinout/Wiring diagram for Siemens ECU for Renault 237106288r EMS3155? Renault Megane IV 2016. I tried to read on bench with pcmtuner but no luck. Thank you Solution: Try module module 59: 1.2T EMS3155 UDS (TC1782/2.5MB) or module 22: Nissan: Juke 1.2T EMS3155 (TC1782/2560KB) you can try, UDS requires immobiliser authorization on many ECU so cannot do bench just read it in obd with pcm tuner . not start in bench because immo active and key.
Read more

Foxflash Update DCM7.24 E38 E92 E83 E0 E39A via OBD

Image
 What's the difference between Foxflash and the new KT200 II 2nd generation ecu/tcu programmer? Foxflash: free online update to get more protocols. KT200 II: it's a separate new hardware with new protocols Foxflash: more stable KT200: less stable, often bricks ECU Foxflash: reading and writing is faster and stable in the long run. Direct update foxflash online to get KT200 II protocols for example: Marelli 8GMC BENCH Delco E38 OBD BENCH E67 BENCH E84 BENCH E92 OBD BENCH SIM2K-305 BOOT Bosch MG1CA007 BENCH Delphi DCM7.24 OBD Phoenix L40 OBD EDC17C11 BENCH BOOT MD1CS069 OBD BENCH New Clone function MEDC17 FCA HYUNDAI JAGUAR LAND ROVER SUZUKI TOYOTA Transmission protocols BOSH 6L45 6L50 6L80 6L90 BENCH see http://www.pcmtuner.org/foxflash-update-dcm7-24-e38-e92-e83-e0-e39a-via-obd/ Users are allowed to update the above protocols to foxflash directly online without purchasing any new hardware or adapters. Foxflash will continue to update more ECU/TCU prot...
Read more

Foxflash, KESS3, Flex: Read Fiat Marelli 9DF ECU Easily

Image
 To read Fiat Magneti Marelli IAW 9DF ECU, you have 3 options: 1.Flex in boot mode You have to open the ecu or make a hole in the center of the inscription "Magneti" Marelli" and connect the starter through the hole With Flex you can have a vr file but it doesn’t can’t write in obd. 2. Use Kess3 , Foxflash , fgtech, autotuner for obd read and obd write (To read, you need 2 hours, to write 10/15 minutes) it makes a Reading in 2h23 For mj9dfhw001 fiat ducato using foxflash. HW001 obd Hw002 boot, 5 minutes of work with opening the computer, FoxFlash takes a long time to read and write. with kess3 OBD 1:30 reading, 15 min writing. with autotuner, he does it pretty fast but only in virtual reading and reading and writing via Obd 3. Use ktag, fgtech, dfox, in jtag by open ecu. FYI: Depends on hardware version. bench is the same 2.30 hours of reading and but sometimes impossible to write. HW000 is ok to write on bench. 0001 0002 impossible to write a mod. R...
Read more