Foxflash V1.4.3.1 Asks for Activation After Update

 Problem: I have foxflash manager version 1.4.1 when instart it it says newer update is available 1.4.3.1. After update, it asks to contact the vendor to activate. Do I need to activate it again?


Foxflash 1.4.3.1 Contact Vendor to Active

Solution:

Yes, in this case, you need to contact us to activate Foxflash.

Send the device serial number and register email to us to activate software via Teamviewer.


Contact

Whatsapp:+8618046220975

Email:Sales@iECUtool.eu

www.iecutool.eu

Comments

Post a Comment

Popular posts from this blog

PCMTuner Unlock Audi SIMOS 8.6 in BSL Mode

Image
 SIMOS 8.6 requires unlocking in BSL mode by the appropriate module. BSL is usually boot mode for unlock. Same as PCR2.1 . Example: Audi A7 2012 2.8 fsi simos 8.6 unlock, after read/write simos8.6 with pcmtuner successfully. all resistor 1 kom How to work with blocks that require unlocking (PCR2.1, SIMOS8.6): 1) Check the current lock status in the car, if the check is disabled, you can go to read-write, otherwise follow the instructions 2) Remove the unit from the car, open it, transfer the processor to BSL mode using the connection below (PCR2.1, SIMOS8.6), the work as a whole as in the package 53 (you can use tools like powerbox, and you can do without them) SIMOS8.6 Unlock pcmtuner pinout Red — +12, Black — GND, Yellow — CAN-HIGH, Blue — CAN-LOW 3) Choose "SIMOS8.6 (EEPROM/UNLOCK/BSL) or PCR2.1 (EEPROM/UNLOCK/BSL)" depending of ECU type 4) Click Identification — save ECU data somewhere in a text file. 5) Click Read — save the EEPROM 6) Given that EC...
Read more

PCMTuner Renault EMS3155 ECU Pinout

Image
 Question: Has someone maybe pinout/Wiring diagram for Siemens ECU for Renault 237106288r EMS3155? Renault Megane IV 2016. I tried to read on bench with pcmtuner but no luck. Thank you Solution: Try module module 59: 1.2T EMS3155 UDS (TC1782/2.5MB) or module 22: Nissan: Juke 1.2T EMS3155 (TC1782/2560KB) you can try, UDS requires immobiliser authorization on many ECU so cannot do bench just read it in obd with pcm tuner . not start in bench because immo active and key.
Read more

Foxflash Update DCM7.24 E38 E92 E83 E0 E39A via OBD

Image
 What's the difference between Foxflash and the new KT200 II 2nd generation ecu/tcu programmer? Foxflash: free online update to get more protocols. KT200 II: it's a separate new hardware with new protocols Foxflash: more stable KT200: less stable, often bricks ECU Foxflash: reading and writing is faster and stable in the long run. Direct update foxflash online to get KT200 II protocols for example: Marelli 8GMC BENCH Delco E38 OBD BENCH E67 BENCH E84 BENCH E92 OBD BENCH SIM2K-305 BOOT Bosch MG1CA007 BENCH Delphi DCM7.24 OBD Phoenix L40 OBD EDC17C11 BENCH BOOT MD1CS069 OBD BENCH New Clone function MEDC17 FCA HYUNDAI JAGUAR LAND ROVER SUZUKI TOYOTA Transmission protocols BOSH 6L45 6L50 6L80 6L90 BENCH see http://www.pcmtuner.org/foxflash-update-dcm7-24-e38-e92-e83-e0-e39a-via-obd/ Users are allowed to update the above protocols to foxflash directly online without purchasing any new hardware or adapters. Foxflash will continue to update more ECU/TCU prot...
Read more