OBDSTAR DC706: Read Mahindra EDC16C39 ECU

 Today we are going to read Mahindra Bosch EDC16C39 ECU with OBDSTAR DC706 and P003+ adapter. For some EDC16 ECUs you must use P003+ or MP001, old P003 does not work.

12 volt supply will be required.


OBDSTAR DC706 Read and Write Bosch EDC16C39 with P003+

Go to ECM function, quick search EDC16C39 and select EDC16C39 MPC561(2)+ M588W016D(F)B

Choose Bench mode with P003+ adapter


OBDSTAR DC706 Read and Write Bosch EDC16C39 with P003+
OBDSTAR DC706 Read and Write Bosch EDC16C39 with P003+

Check wiring diagram

Then connect DC706 with EDC16 ECU via P003+


OBDSTAR DC706 Read and Write Bosch EDC16C39 with P003+
OBDSTAR DC706 Read and Write Bosch EDC16C39 with P003+

Connect ECM


OBDSTAR DC706 Read and Write Bosch EDC16C39 with P003+

Read EXT eeprom and save

Read EXT flash and save.

Write EXT eeprom


OBDSTAR DC706 Read and Write Bosch EDC16C39 with P003+

Write EXT eeprom successfully

Write EXT flash


OBDSTAR DC706 Read and Write Bosch EDC16C39 with P003+
OBDSTAR DC706 Read and Write Bosch EDC16C39 with P003+

Write EXT flash successfully.

www.iecutool.eu

Comments

Post a Comment

Popular posts from this blog

PCMTuner Chevrolet SIM2K-D160 ECU Pinout

Image
 How to read a Chevrolet SIM2K-D160 ecu with pcmtuner ? Use this in Module 30, 1,3,5 — ECU ground (just connect one of the contacts) 77 — CAN-High 78 — CAN-Low 76 — K-Line 2 — +12V (ignition on) 4 — +12V (power supply of the main relay) 6 — +12V (non-switchable power supply) You may not be able to do this ECU in BSL 53 as main processor is MPC756MXP56 Second Processor TC1738. You could try OBD Module 30 Kia/Hyundai SIM2K 2.0L, 2.5L (SIM2K-D160) But failing that, you would have to do this in BSL mode 53 http://www.pcmtuner.org/pcmtuner-module-53-infineon-tricore-bsl-operation/
Read more

Foxflash Pinout to Mercedes SIEMENS VDO MSM2.0

Image
  Foxflash programmer will read and write Mercedes Benz gasoline SIEMENS VDO MSM2.0 ECU on bench. Here is the fox flash pinout to MSM 2.0. Select driver Mercedes Siemens ECUS 1.4/1.6 Siemends VDO MSM 2.0 FULL SYSTEM If old and new ecu have read flash and eeprom without problem. Write not work with foxflash. Have error. Cannot write any file as shown image below: After read flash/eprom — Disconnect ecu and restart software (unplug foxflash ) — restart Then connect again, Write flash, Also try lower power only need 13v on this ecu.
Read more

Foxflash Update DCM7.24 E38 E92 E83 E0 E39A via OBD

Image
 What's the difference between Foxflash and the new KT200 II 2nd generation ecu/tcu programmer? Foxflash: free online update to get more protocols. KT200 II: it's a separate new hardware with new protocols Foxflash: more stable KT200: less stable, often bricks ECU Foxflash: reading and writing is faster and stable in the long run. Direct update foxflash online to get KT200 II protocols for example: Marelli 8GMC BENCH Delco E38 OBD BENCH E67 BENCH E84 BENCH E92 OBD BENCH SIM2K-305 BOOT Bosch MG1CA007 BENCH Delphi DCM7.24 OBD Phoenix L40 OBD EDC17C11 BENCH BOOT MD1CS069 OBD BENCH New Clone function MEDC17 FCA HYUNDAI JAGUAR LAND ROVER SUZUKI TOYOTA Transmission protocols BOSH 6L45 6L50 6L80 6L90 BENCH see http://www.pcmtuner.org/foxflash-update-dcm7-24-e38-e92-e83-e0-e39a-via-obd/ Users are allowed to update the above protocols to foxflash directly online without purchasing any new hardware or adapters. Foxflash will continue to update more ECU/TCU prot...
Read more