Foxflash: Read/Write Bosch MG1CS111 on 2019 Seat Leon

 Foxflash new user report:

Seat Leon 2.0 TSI 2019
Bosch MG1CS111. Not Simos 18. On this one it’s a Bosch mg1cs111.
Read ok
Write ok
Stage 1 par Stgfiles
Checksum by Foxflash
Perfectly.

Image attached:


Foxflash Read and Write Seat Leon 2019 MG1CS111
Foxflash Read and Write Seat Leon 2019 MG1CS111
Foxflash Read and Write Seat Leon 2019 MG1CS111
Foxflash Read and Write Seat Leon 2019 MG1CS111
Foxflash Read and Write Seat Leon 2019 MG1CS111


Comments

Post a Comment

Popular posts from this blog

PCMTuner Unlock Audi SIMOS 8.6 in BSL Mode

Image
 SIMOS 8.6 requires unlocking in BSL mode by the appropriate module. BSL is usually boot mode for unlock. Same as PCR2.1 . Example: Audi A7 2012 2.8 fsi simos 8.6 unlock, after read/write simos8.6 with pcmtuner successfully. all resistor 1 kom How to work with blocks that require unlocking (PCR2.1, SIMOS8.6): 1) Check the current lock status in the car, if the check is disabled, you can go to read-write, otherwise follow the instructions 2) Remove the unit from the car, open it, transfer the processor to BSL mode using the connection below (PCR2.1, SIMOS8.6), the work as a whole as in the package 53 (you can use tools like powerbox, and you can do without them) SIMOS8.6 Unlock pcmtuner pinout Red — +12, Black — GND, Yellow — CAN-HIGH, Blue — CAN-LOW 3) Choose "SIMOS8.6 (EEPROM/UNLOCK/BSL) or PCR2.1 (EEPROM/UNLOCK/BSL)" depending of ECU type 4) Click Identification — save ECU data somewhere in a text file. 5) Click Read — save the EEPROM 6) Given that EC...
Read more

How to Find Bosch ECU Serial Numbers and Correct Pinouts

Image
 Here is basic post for people asking basic questions, apparently now on high demand since we have gathered again new members in our ECU group . So you got bosch ecu in hand from car and how to figure out how to identify it and what pinout to use? On this case we can randomly take one bosch ecu that we will identify. So all bosch ecus start with serial numbers 028… 026. We just head to bosches page next https://www.bosch-repair-service.com/ Here you search by oe or bosch number, i have random bosch ecu here and it’s 0 281 014 544 and bosch page ends up with a result. We can see its edc16cp35. Now there are two ways. Either to search in foxflash bmw / edc16cp35 for pinout. Or we head to ecu pinout page and figure out pinout from there. One of the best online pinout catalogs can be found at ecu desing, So save webpage https://ecu.design/ecu-pinout/ Copy address and head out there. Type in edc16cp35, bmw uses two processors in this one mpc 562 and mpc564. Pinouts jus...
Read more

Foxflash, KESS3, Flex: Read Fiat Marelli 9DF ECU Easily

Image
 To read Fiat Magneti Marelli IAW 9DF ECU, you have 3 options: 1.Flex in boot mode You have to open the ecu or make a hole in the center of the inscription "Magneti" Marelli" and connect the starter through the hole With Flex you can have a vr file but it doesn’t can’t write in obd. 2. Use Kess3 , Foxflash , fgtech, autotuner for obd read and obd write (To read, you need 2 hours, to write 10/15 minutes) it makes a Reading in 2h23 For mj9dfhw001 fiat ducato using foxflash. HW001 obd Hw002 boot, 5 minutes of work with opening the computer, FoxFlash takes a long time to read and write. with kess3 OBD 1:30 reading, 15 min writing. with autotuner, he does it pretty fast but only in virtual reading and reading and writing via Obd 3. Use ktag, fgtech, dfox, in jtag by open ecu. FYI: Depends on hardware version. bench is the same 2.30 hours of reading and but sometimes impossible to write. HW000 is ok to write on bench. 0001 0002 impossible to write a mod. R...
Read more