Alientech KESS3 Update: Siemens ECU Cloning Made Easy

 Alientech KESS3 New protocol update-Remap and clone the Siemens SIM4LKE and Siemens EMS2214 ECUs equipped on Mercedes-Benz and Ford vehicles.

Offer a comprehensive service to your customers thanks to new protocols for KESS3.


Alientech KESS3 Adds Siemens SIM4LKE and EMS2214 Cloning
 

LATEST UPDATES AND NEWS FROM THE ALIENTECH WORLD!

UPGRADE 1.98

 

Increase job opportunities for your workshop with two new developments dedicated to some older vehicles. Work with the "BOOT" bench mode to optimize performance and particularly for repairing Siemens SIM4LKE and EMS2214 ECUs equipped on Mercedes-Benz Kompressor and Ford Duratec engines.

Focus on the new ECUs:

 
  • Siemens SIM4LKE
  • Siemens EMS2214
 

Choose how to operate on thousands of ECUs, in the connection mode you prefer, depending on the type of work required by your customers.

Benz

Read, Write and Clone in Boot Mode


Alientech KESS3 Adds Siemens SIM4LKE and EMS2214 Cloning
Alientech KESS3 Adds Siemens SIM4LKE and EMS2214 Cloning

Ford

Read, Write and Clone in Boot Mode

Fiesta - 1.6 Duratec TI-VCT 5MT — Petrol — 88 kW

 

Activate the CAR — BENCH/BOOT protocols now and work 360° for maximum customer satisfaction.

 

Comments

Post a Comment

Popular posts from this blog

FoxFlash Read and Write Volvo Denso MB279700-9xxx

Image
 Foxflash Volvo Denso MB279700–9xxx works perfectly, just follow the steps of foxflash , reading, unlocking, and writing all done on the bench. PROCEDURE: 1 — Read the Ecu AND unlock the Ecu 2 — Write the ECU READING AND UNLOCKING: Connect the following pinout using the multifunction cable. Start the driver: CAR > VOLVO > TOOLS VOLVO >UNLOCK DENSO MB279700 9641 SH72546R CAN Click on the READ FILE button to read the file. After reading, click on the UNLOCK button to unlock and enable the writing of the control unit. WRITING: Now it will be possible to reconnect the control unit to the car and write the modified file via OBD. Use the following driver: CAR > VOLVO > Model >2.0 DENSO MB279700 9641 SH72546R CAN Alternatively, you can WRITE also the ECU on the table using the pinout on the next page. Note: Compared to the read pinout, the CAN line is moved. FOXFLASH PINOUT FOR WRITING: Just follow the foxflash instructions: read file 15 min, unlock
Read more

Read/Write BMW MSV70 DME by Foxflash, Ktag or FC200?

Image
 Which tool to read this computer BMW MSV70 DME? Foxflash : Yes, via BDM Jtag Connect multifunction cable as follows: Solder the dip/sip connectors on the pcb and do a link: Insert Siemens/Marelli adapter as in photo: To read and write use the following driver: → BDM/ JTAG MODE → BDM MPC → MPC55x/56x Ktag / Kess V2 : Need luck. The best option is BDM. Sometimes Kess v2 and ktag clone read ok but failed during writing, checksum error. Ori Kess done well OBD but takes long. Easy to remove and run in bdm. CG FC200: FC200 programmer does not support this computer.
Read more

PCMTuner PSA Bosch MED17.4 Pinout

Image
 I'm trying to read one Bosch MED17.4 from a Peugeot 207 1.6t; ecu pinout is correct, but pcmtuner pcmflash shows failure, I'm using module 71 tc1766 FLASH… So, any clue? Solution: There are 2 types of pinout for med17.4. Try both. see which one works. Bosch MEDV174 IROM TC1766 EGPT PSA Pinout Feedback: Solved. Mine work with type 1 and module 71 TC1766.
Read more