Foxflash Failed to Read Renault SID306 by OBD?

 Foxflash tool failed to read and write Dacia Duster SID306 ECU via OBD? voltage is 13V+.

Foxflash Failed to Read Renault SID306 by OBD

If fail to read SID306 by OBD, try boot mode.

Foxflash SID306 boot pinout

SIEMENS CONTINENTAL SID305/SID306 V.1 [ TC1766 INT.F.] — Renault, Nissan

Read and Write ECU

Connect with the multifunction cable the following pinout and the boot shown below.
Use the driver:
→ TOOLS BOOT MODE
→ INFINEON TRICORE Boot
→ SAK TC1766

Foxflash Failed to Read Renault SID306 by OBD

Foxflash Failed to Read Renault SID306 by OBD

Below we show 2 alternative methods of booting in the absence of the D48CB02 cable.

Foxflash Failed to Read Renault SID306 by OBD

Some hardware versions only boot in the following way:

Foxflash Failed to Read Renault SID306 by OBD

If OBD and boot all fail, the ECU is encrypted and it is not supported by foxflash.

www.iecutool.com

Comments

Post a Comment

Popular posts from this blog

FoxFlash Read and Write Volvo Denso MB279700-9xxx

Image
 Foxflash Volvo Denso MB279700–9xxx works perfectly, just follow the steps of foxflash , reading, unlocking, and writing all done on the bench. PROCEDURE: 1 — Read the Ecu AND unlock the Ecu 2 — Write the ECU READING AND UNLOCKING: Connect the following pinout using the multifunction cable. Start the driver: CAR > VOLVO > TOOLS VOLVO >UNLOCK DENSO MB279700 9641 SH72546R CAN Click on the READ FILE button to read the file. After reading, click on the UNLOCK button to unlock and enable the writing of the control unit. WRITING: Now it will be possible to reconnect the control unit to the car and write the modified file via OBD. Use the following driver: CAR > VOLVO > Model >2.0 DENSO MB279700 9641 SH72546R CAN Alternatively, you can WRITE also the ECU on the table using the pinout on the next page. Note: Compared to the read pinout, the CAN line is moved. FOXFLASH PINOUT FOR WRITING: Just follow the foxflash instructions: read file 15 min, unlock
Read more

Read/Write BMW MSV70 DME by Foxflash, Ktag or FC200?

Image
 Which tool to read this computer BMW MSV70 DME? Foxflash : Yes, via BDM Jtag Connect multifunction cable as follows: Solder the dip/sip connectors on the pcb and do a link: Insert Siemens/Marelli adapter as in photo: To read and write use the following driver: → BDM/ JTAG MODE → BDM MPC → MPC55x/56x Ktag / Kess V2 : Need luck. The best option is BDM. Sometimes Kess v2 and ktag clone read ok but failed during writing, checksum error. Ori Kess done well OBD but takes long. Easy to remove and run in bdm. CG FC200: FC200 programmer does not support this computer.
Read more

PCMTuner PSA Bosch MED17.4 Pinout

Image
 I'm trying to read one Bosch MED17.4 from a Peugeot 207 1.6t; ecu pinout is correct, but pcmtuner pcmflash shows failure, I'm using module 71 tc1766 FLASH… So, any clue? Solution: There are 2 types of pinout for med17.4. Try both. see which one works. Bosch MEDV174 IROM TC1766 EGPT PSA Pinout Feedback: Solved. Mine work with type 1 and module 71 TC1766.
Read more