Foxflash Updates BMW MSV90 Boot and DCM6.2A

 Good news for both new and old Foxflash ecu programmer users, there are some new updates in January, 2023.

Just a note and reminder, any software updates will be done automatically when ready. FOXFLASH WILL AUTO UPDATE WHEN READY!!!

Just connect your tool and keep internet connect , open the manager and foxflash , it will auto update to your local.

When you are online, the update will auto sync from the server to your side.

January 16, 2023

FULL SYSTEM FOR TCU TEMIC 6T50 OPEL, CHEVROLET

– Complete reading and writing of Micro,

– Complete reading and writing of EEPROM,

– Cloning,

– RIVERGIN function

January 20, 2023

– BENCH MODE BY PROCESSOR INFINEON TRICORE TC1782

With this update you will be able to fully read and write the following ECUs directly

from pinout without having to open them:

– VAG GROUP VW-AUDI-SEAT-SKODA: MED17.5.21, MED17.5.25

– FORD: MED17.0.7

– NISSAN: EDC17 C84

– RENAULT: ME17.9.20, EDC17 C84

– TOYOTA: MED17.9.52, EDC17 C47

26 Jan 2023 Update
foxFlash Can Support AUDI VW Group TCU DQ250C/E/F OBD virtual read/write-BENCH Read&Write
foxFlash is now able to perform the following operations:
OBD Virtual Read
OBD Write
BENCH Read
BENCH Write
On the following TCUs:
Temic DQ250C
Temic DQ250E
Temic DQ250F
Vehicles concerned:
AUDI/SKODA/VAG 2.0 TSI/TFSI
AUDI/SKODA/VAG 2.0 TDI CR

January 27, 2023

foxFlash is now able to perform the Toyota Denso Gen1 (76F00xx) OBD read/write

foxFlash is now able to perform the following operations:

  • OBD Read
  • OBD Write

On the following ECU reference:

Denso Gen1 (76F00xx)

  • Hino 4.0 VVT-i 147ch
  • Lexus/Toyota 2.5 205ch
  • Lexus 200H (1.8 E-CVT) 99ch
  • Lexus 220d 177ch
  • Lexus 250 (GSE20) 200ch
  • Lexus 300 (3.0 V6) 204ch
  • Lexus 330 (3.3 V6) 230ch
  • Lexus 350 (3.5i V6) 275/300ch
  • Lexus 400h (3.3i V6) 272ch
  • Lexus 430 290ch
  • Lexus 450h (3.5i V6) 292/299ch
  • Lexus 460h (4.6 V8) 247ch
  • Lexus 600h (5.0 V8) 394ch
  • Toyota 1.0 (1KR-DE) 64ch
  • Toyota 1.3 VVT-i 87/100ch
  • Toyota 1.6 VVT-i 132ch
  • Toyota 1.8 VVT-i HSD/TS 99/129/133ch
  • Toyota 2.0 (1AZFE) 145ch
  • Toyota 2.0 D4-D 116/126ch
  • Toyota 2.0 DOHC 16v 156ch
  • Toyota 2.0i 150ch
  • Toyota 2.2 D4-D 136/150/177ch
  • Toyota 2.4 (2AZFE) 160ch
  • Toyota 2.5 205ch
  • Toyota 2.5 D4-D 101/125/144/150ch
  • Toyota 2.7i 161/188ch
  • Toyota 3.0 D4-D 172ch
  • Toyota 3.5 (2GRFE) 270ch
  • Toyota 3.5i V6 266ch
  • Toyota 4.0 V6 239/249/260/273ch
  • Toyota 4.3 VVT-i 300ch
  • Toyota 4.5 D4-D 272ch
  • Toyota 4.5 V8 D4-D 198ch
  • Toyota 4.6i VVT-i D-45 314ch
  • Toyota 4.7 V8 280/288ch
  • Toyota 5.0 VVT-i 295ch
  • Toyota 5.7i VVT-i D-45 286ch
  • Lexus GS 300
  • Lexus GS 350
  • Lexus IS-F
  • Toyota Prius
  • Toyota RAV 4
  • Toyota Sequoia
  • Toyota Tacoma
  • Toyota Tundra
  • Toyota Verso
  • Toyota Auris
  • Toyota Auris
  • Toyota Avensis
  • Toyota Camry
  • Toyota Corolla (Verso)
  • Toyota Crown
  • Toyota Dyna
  • Toyota Estima
  • Toyota FJ Cruiser
  • Toyota Fortuner
  • Toyota Hilux
  • Toyota Land Cruiser
  • Toyota Mark X
  • Toyota Optimo

January 27, 2023

ECU UPDATE New Protocols for Bentley Skoda (BOSCH )
Today we added multiple protocols for Bentley, Skoda, Honda, Volvo, etc. More info on supported ECUs and cars can be found below.
SUPPORTED CONTROL UNITS & VEHICLES
BENCH /BOOT/OBD
BOSCH
BAIC Bosch ME17.8.8 TC1728: Senova x25 1.5 VTI (2016), Senova X35 1.5 VTI (2016) , BJ20 1.5 VTI (2016)(BOOT)
Honda Bosch ME17.9.55 TC1724: City/Jazz/BRIO/FIT 1.2L i-VTEC (2014)(BOOT)
Mahindra Bosch EDC17C53 TC1767: XUV500 2.2 CRD (2014)(BENCH BOOT)
Bentley Bosch MG1CS163 TC298: Continental GT W12 6.0 (2018)(BENCH)
Volvo Bosch EDC16C34 MPC562: V70/S80 1.6D (2010)(OBD BENCH JTAG)
Skoda Bosch MED17.1.27: Fabia 1.0 TSI (2017)(OBD BENCH BOOT)
Bentley Bosch MED17.1.62: Bentayga W12 6.0 (2016)(BENCH BOOT)

January 27, 2023

1. BMW MSV90 Protocols BOOT Mode

This time it is for BMW cars with Siemens MSV90 TC1796 ECU. More info on supported cars can be found below.
SUPPORTED CONTROL UNITS & VEHICLES
BOOT
SIEMENS
MSV90 TC1796
CARS:
BMW 5 Series F10–530i N53B30A/N52B30B
BMW 5 Series F11–530i N53B30A/N52B30B
BMW 7 Series F01–730Li N52B30A/N52B30B
BMW 7 Series F02–730Li N52B30A/N52B30B
BMW X3 Series F25–28i xDrive N52B30A/N52B30B

2. Delphi DCM6.2AP DCM6.2A DCM6.2C DCM6.2V update

Support for all Delphi DCM6.2AP/A/C/V
foxFlash is now able to perform the following operations: on DCM6.2A/C/V
OBD Read
OBD Write
JTAG_BOOT
DCM6.2AP with JTAG_BOOT On the following manufacturer ECU's:
Hyundai
Audi
Citroen
Fiat
Kia
MAN
Peugeot
VW
Toyota
Ssangyong

Comments

Post a Comment

Popular posts from this blog

PCMTuner Unlock Audi SIMOS 8.6 in BSL Mode

Image
 SIMOS 8.6 requires unlocking in BSL mode by the appropriate module. BSL is usually boot mode for unlock. Same as PCR2.1 . Example: Audi A7 2012 2.8 fsi simos 8.6 unlock, after read/write simos8.6 with pcmtuner successfully. all resistor 1 kom How to work with blocks that require unlocking (PCR2.1, SIMOS8.6): 1) Check the current lock status in the car, if the check is disabled, you can go to read-write, otherwise follow the instructions 2) Remove the unit from the car, open it, transfer the processor to BSL mode using the connection below (PCR2.1, SIMOS8.6), the work as a whole as in the package 53 (you can use tools like powerbox, and you can do without them) SIMOS8.6 Unlock pcmtuner pinout Red — +12, Black — GND, Yellow — CAN-HIGH, Blue — CAN-LOW 3) Choose "SIMOS8.6 (EEPROM/UNLOCK/BSL) or PCR2.1 (EEPROM/UNLOCK/BSL)" depending of ECU type 4) Click Identification — save ECU data somewhere in a text file. 5) Click Read — save the EEPROM 6) Given that EC...
Read more

How to Find Bosch ECU Serial Numbers and Correct Pinouts

Image
 Here is basic post for people asking basic questions, apparently now on high demand since we have gathered again new members in our ECU group . So you got bosch ecu in hand from car and how to figure out how to identify it and what pinout to use? On this case we can randomly take one bosch ecu that we will identify. So all bosch ecus start with serial numbers 028… 026. We just head to bosches page next https://www.bosch-repair-service.com/ Here you search by oe or bosch number, i have random bosch ecu here and it’s 0 281 014 544 and bosch page ends up with a result. We can see its edc16cp35. Now there are two ways. Either to search in foxflash bmw / edc16cp35 for pinout. Or we head to ecu pinout page and figure out pinout from there. One of the best online pinout catalogs can be found at ecu desing, So save webpage https://ecu.design/ecu-pinout/ Copy address and head out there. Type in edc16cp35, bmw uses two processors in this one mpc 562 and mpc564. Pinouts jus...
Read more

FoxFlash Read and Write Volvo Denso MB279700-9xxx

Image
 Foxflash Volvo Denso MB279700–9xxx works perfectly, just follow the steps of foxflash , reading, unlocking, and writing all done on the bench. PROCEDURE: 1 — Read the Ecu AND unlock the Ecu 2 — Write the ECU READING AND UNLOCKING: Connect the following pinout using the multifunction cable. Start the driver: CAR > VOLVO > TOOLS VOLVO >UNLOCK DENSO MB279700 9641 SH72546R CAN Click on the READ FILE button to read the file. After reading, click on the UNLOCK button to unlock and enable the writing of the control unit. WRITING: Now it will be possible to reconnect the control unit to the car and write the modified file via OBD. Use the following driver: CAR > VOLVO > Model >2.0 DENSO MB279700 9641 SH72546R CAN Alternatively, you can WRITE also the ECU on the table using the pinout on the next page. Note: Compared to the read pinout, the CAN line is moved. FOXFLASH PINOUT FOR WRITING: Just follow the foxflash instructions: read file 15 min, unl...
Read more