Fetrotech Tool Failed to Read Renault EDC16CP33?

 Problem:

I have an ecu edc16cp33 Laguna 3 which is supported by fetrotech tool.
Fetrotech can't find ecu on the 3 pinout available.

And i can't find boot pinout fetrotech

Please help

Solution:

Problem with EDC16CP33 is there are 2 processor types (MPC561 and MPC564) only one is supported.

Do it with K-tag. Also read eeprom. With ktag you can access processor and eeprom directly, so even if ECU itself is damaged it won't effect direct processor reading.

Comments

Post a Comment

Popular posts from this blog

Foxflash Update DCM7.24 E38 E92 E83 E0 E39A via OBD

Image
 What's the difference between Foxflash and the new KT200 II 2nd generation ecu/tcu programmer? Foxflash: free online update to get more protocols. KT200 II: it's a separate new hardware with new protocols Foxflash: more stable KT200: less stable, often bricks ECU Foxflash: reading and writing is faster and stable in the long run. Direct update foxflash online to get KT200 II protocols for example: Marelli 8GMC BENCH Delco E38 OBD BENCH E67 BENCH E84 BENCH E92 OBD BENCH SIM2K-305 BOOT Bosch MG1CA007 BENCH Delphi DCM7.24 OBD Phoenix L40 OBD EDC17C11 BENCH BOOT MD1CS069 OBD BENCH New Clone function MEDC17 FCA HYUNDAI JAGUAR LAND ROVER SUZUKI TOYOTA Transmission protocols BOSH 6L45 6L50 6L80 6L90 BENCH see http://www.pcmtuner.org/foxflash-update-dcm7-24-e38-e92-e83-e0-e39a-via-obd/ Users are allowed to update the above protocols to foxflash directly online without purchasing any new hardware or adapters. Foxflash will continue to update more ECU/TCU prot...
Read more

PCMTuner Chevrolet SIM2K-D160 ECU Pinout

Image
 How to read a Chevrolet SIM2K-D160 ecu with pcmtuner ? Use this in Module 30, 1,3,5 — ECU ground (just connect one of the contacts) 77 — CAN-High 78 — CAN-Low 76 — K-Line 2 — +12V (ignition on) 4 — +12V (power supply of the main relay) 6 — +12V (non-switchable power supply) You may not be able to do this ECU in BSL 53 as main processor is MPC756MXP56 Second Processor TC1738. You could try OBD Module 30 Kia/Hyundai SIM2K 2.0L, 2.5L (SIM2K-D160) But failing that, you would have to do this in BSL mode 53 http://www.pcmtuner.org/pcmtuner-module-53-infineon-tricore-bsl-operation/
Read more

Foxflash, KESS3, Flex: Read Fiat Marelli 9DF ECU Easily

Image
 To read Fiat Magneti Marelli IAW 9DF ECU, you have 3 options: 1.Flex in boot mode You have to open the ecu or make a hole in the center of the inscription "Magneti" Marelli" and connect the starter through the hole With Flex you can have a vr file but it doesn’t can’t write in obd. 2. Use Kess3 , Foxflash , fgtech, autotuner for obd read and obd write (To read, you need 2 hours, to write 10/15 minutes) it makes a Reading in 2h23 For mj9dfhw001 fiat ducato using foxflash. HW001 obd Hw002 boot, 5 minutes of work with opening the computer, FoxFlash takes a long time to read and write. with kess3 OBD 1:30 reading, 15 min writing. with autotuner, he does it pretty fast but only in virtual reading and reading and writing via Obd 3. Use ktag, fgtech, dfox, in jtag by open ecu. FYI: Depends on hardware version. bench is the same 2.30 hours of reading and but sometimes impossible to write. HW000 is ok to write on bench. 0001 0002 impossible to write a mod. R...
Read more