PCMtuner-tool

  Problem: I have tried to read this ECU Bosch ME7.6.2 through the Alientech KESS3 Bench mode and it’s doesn’t respond. Does its mean the ECU is damaged? Any help? Possible solutions to KESS3 ECU communication error: 1. The device does not respond to communication with the ECU, maybe you can try changing the voltage (Power supply) to a more suitable one. 2. Sometimes you have to try many times. Always double and triple check connections. 3. There is a possibility that the protocol is not working. Check coverage before reading. 4. The ECU is damaged. 5. Open a ticket and seek help from Alientech technicians. www.iecutool.eu

  Problem: Foxflash not connecting with Audi a4 2017 EDC17CP74 ECU. Any advise? Solution: Try another pinout V2. Use pinout from Pinout from ktag or dimsport. V2 pin out is not in foxflash. Feedback: All working now this was Audi A4 a 2017 edc17cp74. V2 pinout is slightly different with can high and low. Worked it out this is v2 can h can l are next to ignition wire all working now. www.iecutool.eu

  Alientech KESS3 released ECU- Isuzu Denso 276700–2051 on May 6th, 2024. Work on bench in "BENCH" mode for tuning, optimizing fuel consumption, and repairing Isuzu N-Series trucks equipped with Denso 276700–2051 ECUs. Ensure precise and reliable interventions on supported new work vehicles, satisfying your customers. New supported ECU: Denso 276700–2051   Grab this technological advantage to increase your workshop’s earning potential, not only in the heavy-duty sector but across all vehicle types. Read, Write and Clone in Bench Mode Vehicle List: Activate TRUCK/TRACTOR — BENCH/BOOT protocols and provide comprehensive reprogramming services for all supported ECUs www.iecutool.eu

  Foxflash new user report: Iveco EDC7UC31 ECU Read ok Write OK Checksum by foxflash R/W/CS Ok This ecu reads and writes ok on bench. Foxflash pinout to Iveco EDC7UC31 ECU To read and write use the following driver: → BENCH MODE → [Iveco] → MPC561-[Iveco] → EDC7 UC31 www.iecutool.eu

  Problem: Writing problem on Valeo v46.11 psa who has already had this problem and what is the solution? I specify that I have tried with foxflash in obd and bench… Reading and id read without worries. Writing ecu gives error SK1. Solution: Few silent key errors fixes Ecu locked by immobilizer. Boot only Or Was your your car in eco mode when trying to read? Try to Add voltage 14v+ You can also try obd protocol in breakout box connection like in otb adapter. www.iecutool.eu

  Foxflash new user report: VW Passat 2011 1.6 tdi Simos Pcr2.1 Unlock eeprom Benched flash + eprom All in foxflash, all in bench. no problems read/write/checksum correction. How to do pcr2.1? Connect ecu in bench 1.First Read flash -it will save flash + password on flash 2.read eprom 3.now write back same eprom you readed in step 2 -it will ask for obd patch and unlock, select yes. (Eprom unlock) 3. Send flash for modify 4.save mod file in same archive where password is. 5.open mod and write it. (Flash unlock). 6.drop ecu in car and off you go www.iecutool.eu

 Here comes the user feedback on VAG MED17.5.5 ECU: VAG Med17.5.5 tc1766 ECU Foxflash boot mode, error on bench (worng driver selected) So tried tc1767 driver ( software prompts same error ) Original pcmflash on bench also error (too high tprot). Ktag clone also error. Back to foxflash boot mode …error unlock password. Selected Tools boot obd password for vag tprot8+ with different pinout and got the password saved. After that everything went smoothly in boot mode. Normally these bench-jobs don’t take long , this one got a little out of hand but foxflash saved the day after all. www.iecutool.eu