Can Xhorse Multi Prog Clone DQ381 MQB Gearbox?

 Will Xhorse Multi Prog 1：1 clone VAG Bosch DQ381 TCU?

VAG Bosch DQ381 TCU (part number 1034420266), MCU Renesas R5F72549R (SH725xx family), boot version bh1g0301.
From the Multi-Prog (Xhorse) connection log in bench mode, I see:
CPU type: SH725xx
BOSCH part number: 1034420266
TCU type: TCU-2-x.x
MCU: R5F72549R (72549)
UID: E716113C / EF722549R
Flash: 0x2800000x
Int EEPROM: 0x200000
Connection successful, boot bh1g0301
Multi-Prog (latest update) reads internal flash, EEPROM, and maps without issues, but the big question is: Can I do a true 1:1 clone (including OTP/component protection/IMMO data) onto an identical donor unit, or are there locked/OTP zones on the Renesas that prevent a perfect copy?


Will Xhorse Multi Prog Clone VAG Bosch DQ381 Gearbox

Solution:

Yes if it is not MQB system.
We use the godiag gt107 with it and no problem.
No if it’s MQB system you will not be able to clone one to one. Need to transfer files from original to donor.

Better use MMS Flex for this. Flex will 1:1 clone DQ381 TCU.

Comments

Post a Comment

Popular posts from this blog

Compare Launch X-prog3 and Autel XP400 Pro Features

Image
 The Launch X-prog3 is on the same level as the autel xp400 pro where it is more limited? in which the Autel is more powerful? Here is the clue. Launch X-Prog3 (GIII) A professional immobilizer and key programmer, often used with Launch X431 diagnostic tablets (e.g., X431 V+, Pro5, PAD VII). Specializes in ECU/TCU cloning, key programming, and immobilizer functions for a wide range of vehicles. Known for its integration with Launch’s ecosystem and built-in features like MQB AKL sync data calculation. Autel XP400 Pro An advanced key and chip programmer that works with Autel MaxiIM tablets (e.g., IM508, IM608, IM608 Pro). Excels in transponder chip reading/writing, immobilizer functions, and ECU/MCU programming. Offers standalone capabilities on PC but is most powerful when paired with Autel MaxiIM tools. Comparison Table Pros and Cons Launch X-Prog3 Pros: Excellent for ECU/TCU cloning. Built-in MQB AKL sync calculator for VW/Audi. Seamless integration wi...
Read more

Foxflash Pinout to Mercedes SIEMENS VDO MSM2.0

Image
  Foxflash programmer will read and write Mercedes Benz gasoline SIEMENS VDO MSM2.0 ECU on bench. Here is the fox flash pinout to MSM 2.0. Select driver Mercedes Siemens ECUS 1.4/1.6 Siemends VDO MSM 2.0 FULL SYSTEM If old and new ecu have read flash and eeprom without problem. Write not work with foxflash. Have error. Cannot write any file as shown image below: After read flash/eprom — Disconnect ecu and restart software (unplug foxflash ) — restart Then connect again, Write flash, Also try lower power only need 13v on this ecu.
Read more

PCMTuner Chevrolet SIM2K-D160 ECU Pinout

Image
 How to read a Chevrolet SIM2K-D160 ecu with pcmtuner ? Use this in Module 30, 1,3,5 — ECU ground (just connect one of the contacts) 77 — CAN-High 78 — CAN-Low 76 — K-Line 2 — +12V (ignition on) 4 — +12V (power supply of the main relay) 6 — +12V (non-switchable power supply) You may not be able to do this ECU in BSL 53 as main processor is MPC756MXP56 Second Processor TC1738. You could try OBD Module 30 Kia/Hyundai SIM2K 2.0L, 2.5L (SIM2K-D160) But failing that, you would have to do this in BSL mode 53 http://www.pcmtuner.org/pcmtuner-module-53-infineon-tricore-bsl-operation/
Read more