New FormulaFlash V1.1.1.0 Supports EMS2215 and EMS6104

 FormulaFlash major update is LIVE!

Version 1.1.1.0

Update Date: Jan 20th
Get ready to unlock more ECUs, more power, and more control with the latest FormulaFlash upgrade!
This update brings extended coverage and enhanced read/write capabilities across multiple platforms.

What’s New in This Update:
Toyota Gen 4 — BENCH Mode
Read / Write + Checksum
• LC300 3.3TD
• LC300 / LX600 / Tundra 3.5T
• LS500 / Tundra 3.5T
• NX / RX / ES / LC / RX450h / Camry / RAV4
• Yaris GR 1.6T (MCU)

SIMOS Series
SIMOS15.10 — OBD Read / Write + Checksum
Ford ECUs
ESU-415 MPC561 — BENCH Read / Write
EMS2215 TC1738 — BENCH Read / Write

Continental / Siemens
EMS6104 — BOOT Read / Write + Checksum
SIM2K-47 ECM & TCM (SAK-C167) — BOOT Read / Write + Checksum

Why Update FormulaFlash?
Expanded ECU support
Reliable Read/Write operations
Integrated checksum correction
Built for professionals who demand precision
Upgrade now and stay ahead of the game with FormulaFlash!


FormulaFlash V1.1.1.0 Update Simos15.10 EMS2215 EMS6104 ECUs
FormulaFlash V1.1.1.0 Update Simos15.10 EMS2215 EMS6104 ECUs


Comments

Post a Comment

Popular posts from this blog

Foxflash Pinout to Mercedes SIEMENS VDO MSM2.0

Image
  Foxflash programmer will read and write Mercedes Benz gasoline SIEMENS VDO MSM2.0 ECU on bench. Here is the fox flash pinout to MSM 2.0. Select driver Mercedes Siemens ECUS 1.4/1.6 Siemends VDO MSM 2.0 FULL SYSTEM If old and new ecu have read flash and eeprom without problem. Write not work with foxflash. Have error. Cannot write any file as shown image below: After read flash/eprom — Disconnect ecu and restart software (unplug foxflash ) — restart Then connect again, Write flash, Also try lower power only need 13v on this ecu.
Read more

PCMTuner Chevrolet SIM2K-D160 ECU Pinout

Image
 How to read a Chevrolet SIM2K-D160 ecu with pcmtuner ? Use this in Module 30, 1,3,5 — ECU ground (just connect one of the contacts) 77 — CAN-High 78 — CAN-Low 76 — K-Line 2 — +12V (ignition on) 4 — +12V (power supply of the main relay) 6 — +12V (non-switchable power supply) You may not be able to do this ECU in BSL 53 as main processor is MPC756MXP56 Second Processor TC1738. You could try OBD Module 30 Kia/Hyundai SIM2K 2.0L, 2.5L (SIM2K-D160) But failing that, you would have to do this in BSL mode 53 http://www.pcmtuner.org/pcmtuner-module-53-infineon-tricore-bsl-operation/
Read more

Compare Launch X-prog3 and Autel XP400 Pro Features

Image
 The Launch X-prog3 is on the same level as the autel xp400 pro where it is more limited? in which the Autel is more powerful? Here is the clue. Launch X-Prog3 (GIII) A professional immobilizer and key programmer, often used with Launch X431 diagnostic tablets (e.g., X431 V+, Pro5, PAD VII). Specializes in ECU/TCU cloning, key programming, and immobilizer functions for a wide range of vehicles. Known for its integration with Launch’s ecosystem and built-in features like MQB AKL sync data calculation. Autel XP400 Pro An advanced key and chip programmer that works with Autel MaxiIM tablets (e.g., IM508, IM608, IM608 Pro). Excels in transponder chip reading/writing, immobilizer functions, and ECU/MCU programming. Offers standalone capabilities on PC but is most powerful when paired with Autel MaxiIM tools. Comparison Table Pros and Cons Launch X-Prog3 Pros: Excellent for ECU/TCU cloning. Built-in MQB AKL sync calculator for VW/Audi. Seamless integration wi...
Read more