New ECUs Added in FormulaFlash Version 1.0.8.0 Update

 FormulaFlash ECU TCU programmer released new software version 1.0.8.0 on December 1st, 2025.

V1.0.8.0

Adds following ECU types:

Volvo
EDC15C11–3.XNO1
EDC15C11–4.X250KNO1
EDC15C11–4.X500KNO1
EDC15C11–3.XNO2
EDC15C11–4.X250KNO2
EDC15C11–4.X 500K NO2
EDC15C3 KLINE NO1
EDC15C3 KLINE NO2
EDC15C7 KLINE

Opel
ME1.55 KLINE
ME7.6H4 KLINE
ME7.6.1 KLINE
ME7.6.2 KLINE
ME7.6.1 KLINE
ME7.6.2 KLINE

JAGUAR
P3.ONA 4.2SC, 4.2 V8 V8SC, 4.2SC

LANDROVER
P3.ONA 4.2SC, LANDROVER AJ33 4.2

MITSUBISHI
64F7058, 64F7059

Mercedes-Benz
ME9.7 Read/Write +CKS

China Ruiyi Tech
TR40 BENCH read&write by bench

China Bosch
ME7.5.20 EEPROM+FLASH Read/Write
ME7.5.30 EEPROM+FLASH Read/Write
ME7.9.7 EEPROM+FLASH Read/Write
ME7.9.7 Two Models DTC OFF

CONTINENTAL/Siemens
SIMK43 AT ECM FLASH Read/Write
SIMK43 AT TCM FLASH Read/Write

China Delphi Series
MT62.1 MT22.3
MT62.1U MT62.1
MT95.1 MT62.3
MT62.1

MG1US/MG1U Read/Write Flash LASH and EEPROM + CKS+ Clone
BMW: MSD81 Coolant Temperature Calibration


FormulaFlash V1.0.8.0 Adds More Volvo Opel JLR Benz ECUs


Comments

Post a Comment

Popular posts from this blog

PCMTuner Chevrolet SIM2K-D160 ECU Pinout

Image
 How to read a Chevrolet SIM2K-D160 ecu with pcmtuner ? Use this in Module 30, 1,3,5 — ECU ground (just connect one of the contacts) 77 — CAN-High 78 — CAN-Low 76 — K-Line 2 — +12V (ignition on) 4 — +12V (power supply of the main relay) 6 — +12V (non-switchable power supply) You may not be able to do this ECU in BSL 53 as main processor is MPC756MXP56 Second Processor TC1738. You could try OBD Module 30 Kia/Hyundai SIM2K 2.0L, 2.5L (SIM2K-D160) But failing that, you would have to do this in BSL mode 53 http://www.pcmtuner.org/pcmtuner-module-53-infineon-tricore-bsl-operation/
Read more

Foxflash Pinout to Mercedes SIEMENS VDO MSM2.0

Image
  Foxflash programmer will read and write Mercedes Benz gasoline SIEMENS VDO MSM2.0 ECU on bench. Here is the fox flash pinout to MSM 2.0. Select driver Mercedes Siemens ECUS 1.4/1.6 Siemends VDO MSM 2.0 FULL SYSTEM If old and new ecu have read flash and eeprom without problem. Write not work with foxflash. Have error. Cannot write any file as shown image below: After read flash/eprom — Disconnect ecu and restart software (unplug foxflash ) — restart Then connect again, Write flash, Also try lower power only need 13v on this ecu.
Read more

Compare Launch X-prog3 and Autel XP400 Pro Features

Image
 The Launch X-prog3 is on the same level as the autel xp400 pro where it is more limited? in which the Autel is more powerful? Here is the clue. Launch X-Prog3 (GIII) A professional immobilizer and key programmer, often used with Launch X431 diagnostic tablets (e.g., X431 V+, Pro5, PAD VII). Specializes in ECU/TCU cloning, key programming, and immobilizer functions for a wide range of vehicles. Known for its integration with Launch’s ecosystem and built-in features like MQB AKL sync data calculation. Autel XP400 Pro An advanced key and chip programmer that works with Autel MaxiIM tablets (e.g., IM508, IM608, IM608 Pro). Excels in transponder chip reading/writing, immobilizer functions, and ECU/MCU programming. Offers standalone capabilities on PC but is most powerful when paired with Autel MaxiIM tools. Comparison Table Pros and Cons Launch X-Prog3 Pros: Excellent for ECU/TCU cloning. Built-in MQB AKL sync calculator for VW/Audi. Seamless integration wi...
Read more