Best Airbag Programmer: CG100 Prog III vs Xhorse Multi Prog

 Today we will compare Xhorse multi prog with CG100 Prog III related to airbags.

Let’s compare the difference between these two programmers.


Launch X431 ECU Programmer Clone GM 6T30 Gearbox

Connect both of them to PC.

CG100 can also automatically repair airbags when you are connected to it. It can repair 90% of airbags. Hhe will write a clear dump. Multi prog can correct some checksums and it does not have subscription and it’s free update.

Multi prog does not have many airbag options.

CG100 has a lot of Fiat, multi prog has only one car. CG100 has many BMW airbags while multiprog has 2 only.
CG100 also has a lot of Benz, Citroen, VAG cars, CG100 is the winner related to European cars.

BMW airbags


Launch X431 ECU Programmer Clone GM 6T30 Gearbox
Launch X431 ECU Programmer Clone GM 6T30 Gearbox

With CG100 you should have subscription if you don’t have these type of chip you are not able to read it.

Citroen airbags


Launch X431 ECU Programmer Clone GM 6T30 Gearbox
Launch X431 ECU Programmer Clone GM 6T30 Gearbox

Benz airbags


Launch X431 ECU Programmer Clone GM 6T30 Gearbox
Launch X431 ECU Programmer Clone GM 6T30 Gearbox

VW airbags


Launch X431 ECU Programmer Clone GM 6T30 Gearbox
Launch X431 ECU Programmer Clone GM 6T30 Gearbox

Multi prog they don’t focus so much on airbags.
The CG company also has the CG70 where you can read quite new airbags on bench. It can make also automatically repairing.

We move to American airbags, you notice on CG100 they are putting the number from the airbag ECU and on multi prog you have car models.

It is much easier to find with numbers. It is quite simple when you have airbag part number. You just type it and you will find very quick.

CG100 also has many Chverole Chrysler airbag models. CG100 can repair Tesla airbags. Multi prog does not have that option.


Launch X431 ECU Programmer Clone GM 6T30 Gearbox
Launch X431 ECU Programmer Clone GM 6T30 Gearbox
Launch X431 ECU Programmer Clone GM 6T30 Gearbox

On Asian cars CG100 programmer is amazing. CG100 does have much more airbags.
For Honda, Hyundai, have lots of chips.
For multi prog, it does not have Mazda, Nissan, Subaru airbag options.

CG100 has a huge list on Nissan and other Asian cars.


Launch X431 ECU Programmer Clone GM 6T30 Gearbox
Launch X431 ECU Programmer Clone GM 6T30 Gearbox

As we said previously, Xhorse multi prog does not focus on airbag while CG100 prog iii is an airbag tool. So they are different tools. Multi prog will read lots of mcu, eeprom, ecus. It also read ISN codes. Multi-prog will read MQB clusters as well. One tool is not enough. Better buy both.

www.iecutool.eu

Comments

Post a Comment

Popular posts from this blog

PCMTuner Unlock Audi SIMOS 8.6 in BSL Mode

Image
 SIMOS 8.6 requires unlocking in BSL mode by the appropriate module. BSL is usually boot mode for unlock. Same as PCR2.1 . Example: Audi A7 2012 2.8 fsi simos 8.6 unlock, after read/write simos8.6 with pcmtuner successfully. all resistor 1 kom How to work with blocks that require unlocking (PCR2.1, SIMOS8.6): 1) Check the current lock status in the car, if the check is disabled, you can go to read-write, otherwise follow the instructions 2) Remove the unit from the car, open it, transfer the processor to BSL mode using the connection below (PCR2.1, SIMOS8.6), the work as a whole as in the package 53 (you can use tools like powerbox, and you can do without them) SIMOS8.6 Unlock pcmtuner pinout Red — +12, Black — GND, Yellow — CAN-HIGH, Blue — CAN-LOW 3) Choose "SIMOS8.6 (EEPROM/UNLOCK/BSL) or PCR2.1 (EEPROM/UNLOCK/BSL)" depending of ECU type 4) Click Identification — save ECU data somewhere in a text file. 5) Click Read — save the EEPROM 6) Given that EC...
Read more

How to Find Bosch ECU Serial Numbers and Correct Pinouts

Image
 Here is basic post for people asking basic questions, apparently now on high demand since we have gathered again new members in our ECU group . So you got bosch ecu in hand from car and how to figure out how to identify it and what pinout to use? On this case we can randomly take one bosch ecu that we will identify. So all bosch ecus start with serial numbers 028… 026. We just head to bosches page next https://www.bosch-repair-service.com/ Here you search by oe or bosch number, i have random bosch ecu here and it’s 0 281 014 544 and bosch page ends up with a result. We can see its edc16cp35. Now there are two ways. Either to search in foxflash bmw / edc16cp35 for pinout. Or we head to ecu pinout page and figure out pinout from there. One of the best online pinout catalogs can be found at ecu desing, So save webpage https://ecu.design/ecu-pinout/ Copy address and head out there. Type in edc16cp35, bmw uses two processors in this one mpc 562 and mpc564. Pinouts jus...
Read more

FoxFlash Read and Write Volvo Denso MB279700-9xxx

Image
 Foxflash Volvo Denso MB279700–9xxx works perfectly, just follow the steps of foxflash , reading, unlocking, and writing all done on the bench. PROCEDURE: 1 — Read the Ecu AND unlock the Ecu 2 — Write the ECU READING AND UNLOCKING: Connect the following pinout using the multifunction cable. Start the driver: CAR > VOLVO > TOOLS VOLVO >UNLOCK DENSO MB279700 9641 SH72546R CAN Click on the READ FILE button to read the file. After reading, click on the UNLOCK button to unlock and enable the writing of the control unit. WRITING: Now it will be possible to reconnect the control unit to the car and write the modified file via OBD. Use the following driver: CAR > VOLVO > Model >2.0 DENSO MB279700 9641 SH72546R CAN Alternatively, you can WRITE also the ECU on the table using the pinout on the next page. Note: Compared to the read pinout, the CAN line is moved. FOXFLASH PINOUT FOR WRITING: Just follow the foxflash instructions: read file 15 min, unl...
Read more