PCMtuner Guide: Ford PSA SID208(SID209) BSL

PCMtuner adds Ford PSA Sid208/Sid209 BSL instructions in the application. You can check the instructions on the PCMtuner software or follow the more detailed instructions below by Marty.

Ford SID208 BSL INSTRUCTIONS
This also applies to SID209 just select this ECU during operations

PCMtuner Module 71 Programming Ford PSA SID208(SID209)

Step 1.
First, with ecu in the car (or on the bench with OBD breakout), we will Identify our ECU
To do this, select 07 SID208 and click Identification

PCMtuner Module 71 Programming Ford PSA SID208(SID209)

Our ECU details can now be seen, If needed we can make a note of these for any future reference.

Step2.
Now we must get the password from the ECU.
To do this we must use the Password option on module 71, and select SID208

PCMtuner Module 71 Programming Ford PSA SID208(SID209)

Step 3.
Now we click the Read button

PCMtuner Module 71 Programming Ford PSA SID208(SID209)

The program extracts the password from the ECU

PCMtuner Module 71 Programming Ford PSA SID208(SID209)

you will now be asked to save it to a file (the serial number of the ECU will be in the file name, it is also indicated on the cover of the ECU itself).
Please remember where you save this file.

PCMtuner Module 71 Programming Ford PSA SID208(SID209)

At same time the program will display the status of the ECU, i.e. whether signature verification is enabled or not.

PCMtuner Module 71 Programming Ford PSA SID208(SID209)

If signature verification is already disabled, then someone has done it before, in this case, just can just write to the ECU as a regular SID208 or SID209.

Step 4.
Open the ECU and, looking at the picture, make the following connection:
Connect 1 kΩ resistors to two via points, connect the end of the resistors to the two upper pads.

PCMtuner Module 71 Programming Ford PSA SID208(SID209)

Always be careful when you open ecu and when you are soldering not to damage components

Step 5.
In the PCM-flash select 53 TC1797 micro and press the Read button

PCMtuner Module 71 Programming Ford PSA SID208(SID209)

The program will ask you to point to a file with a password, you must change from auto to browse and select the file saved in the first step.

PCMtuner Module 71 Programming Ford PSA SID208(SID209)

The ECU Micro memory will now start to read

PCMtuner Module 71 Programming Ford PSA SID208(SID209)

Reading time is around 2–3 minutes., The Full Memory is
Read from the ECU. When Prompted please save the file.

PCMtuner Module 71 Programming Ford PSA SID208(SID209)

Now repeat the above steps for the EEPROM.
Select module 53 TC1997 EEPROM

PCMtuner Module 71 Programming Ford PSA SID208(SID209)

Identification >> read >> select password file >> wait on read >>save EEPROM file
You can Write EEPROM or MICRO back now to ECU, or Remove resistors and Place back in the car and write normally.

When writing file PCMflash
WILL NOT CORRECT CHECKSUM on this ECU –
you must manually do this with winOLS etc

Please UNTICK the Verify/fix crc box before Writing

PCMtuner Module 71 Programming Ford PSA SID208(SID209)

http://www.pcmtuner.org/ford-psa-sid208-sid208-bsl-guide-with-pcmtuner/

Comments

Popular posts from this blog

PCMTuner Unlock Audi SIMOS 8.6 in BSL Mode

How to Find Bosch ECU Serial Numbers and Correct Pinouts

FoxFlash Read and Write Volvo Denso MB279700-9xxx