PCMtuner-tool

 Foxflash new user report: It’s an Isuzu Dmax 2007 3.0d. Foxflash read it via obd on bench. DCM6.2 Delphi ecu Mpc56x Used multimultional adapter without benchbox. Obd protocol read ok. Took 1hr to read. Awaiting for a 5–6 amper power supply for writing to be safe. You can also use OTB adapter on this or gt100 diagtable.

After March 2026, the price of the ECUDESK series ECU chip tuning & remap software will be adjusted, increasing by 20%. Over the past year, ECUDesk has nearly doubled its module library —  from 208 to 410 (+97%)  — reflecting major investment in development, testing, and expanded ECU coverage. To continue improving the product and supporting our reseller network, we are updating our pricing structure. What’s New in 2026? Nearly Double the Modules 208 → 410 supported modules (+97%) New High-Performance Tier: HP+ (Horsepower Plus) Advanced performance tuning capabilities beyond emissions-related modules. New Shortcut Upgrade Option Standard → HP+ for $650 (saves $100 compared to upgrading) Standard → Premium → HP+ New 2026 Pricing Structure Updated Upgrade Paths Standard → Premium: $400 Premium → HP+: $300 Standard → HP+: $650 (new) From March 1, the final discount on the current price list is 20%. Standard: 1000 USD → 800 USD Premium: 1300 USD → 1060 USD HP+: 1500...

It’s a BMW 3D 184hp with Bosch EDC15C4 ECU. Tried Foxflash Full mode but not working(connected everything as shown, measured cables, resistors, outputs everything with multimeter and it’s 100% fine but still no connection) — ERROR SEND WAKE. Simulated OBD on BENCH via K-LINE ok. READ — 5 min WRITE — 2 MIN ONLY FLASH PARTIAL READ!! Checksum with winols. If need to do it via full system mode, need to fix the colored rainbow cable! Problem is rainbow cable inverted, you need to fix the cable.

 Here is the real user’s working experience on VW Passat B7 EDC16CP46 ECU cloning using foxflash : It’s a VW Passat B7 2013 CFFB with Bosch EDC17C46 ECU. The ecu was broken, car didn’ t start, reading on bench was not working. The car wouldn’t start, some water had gotten into the ecu through the plastic plug. The car could be diagnosed on the ecu but there was no error. I tried to read the ecu in the bench but every time it told me to disconnect and reconnect the power and nothing happened. I had another ecu with the same part number from a Passat CC, so I backed it up in the bench. I saw that the one from the car didn’t work in the bench and I tried in boot mode, where initially it didn’t read it, it had to be read the password, I read in the obd mode the password, obd cable connected to the bench, save password on the pc, then I read the ecu for backup in boot mode. I used the cloning module in foxflash where I added the file read in boot from the defective ecu and ...

 How to simulate OBD for Land rover Bosch EDC15C4 ECU using Foxflash programmer ? obd simulation worked with the Godiag GT100 breakout box. It worked with car OBD not full system. Full system doesn’t work. Full system is not about OBD. Just do standard pinout. Read with obd protocol without resistors just k line and + -. Connect both k line for safety. Added photos:

  Problem: I’m having trouble reading this bsi off a Ford Ka (Fiat 500) with OBDSTAR DC706 on bench mode. Tried with and without 120 ohm, no luck. Any suggestions? Solution: Select Ford BSI (Ford BSI Delphi 70F3379+93C86) rather than Fiat BSI. Don’t forget to connect a power supply. Update: Fixed. Important to select Ford for a ka not Fiat, despite the chips being the same! Worked fine when selecting as Ford.

 Will Xhorse Multi Prog 1：1 clone VAG Bosch DQ381 TCU? VAG Bosch DQ381 TCU (part number 1034420266), MCU Renesas R5F72549R (SH725xx family), boot version bh1g0301. From the Multi-Prog (Xhorse) connection log in bench mode, I see: CPU type: SH725xx BOSCH part number: 1034420266 TCU type: TCU-2-x.x MCU: R5F72549R (72549) UID: E716113C / EF722549R Flash: 0x2800000x Int EEPROM: 0x200000 Connection successful, boot bh1g0301 Multi-Prog (latest update) reads internal flash, EEPROM, and maps without issues, but the big question is: Can I do a true 1:1 clone (including OTP/component protection/IMMO data) onto an identical donor unit, or are there locked/OTP zones on the Renesas that prevent a perfect copy? Solution: Yes if it is not MQB system. We use the godiag gt107 with it and no problem. No if it’s MQB system you will not be able to clone one to one. Need to transfer files from original to donor. Better use MMS Flex for this. Flex will 1:1 clone DQ381 TCU.