PCMtuner-tool

 Massive time saver: Iveco EDC16C39 live via 100% OBD! No more ECU removal! You can now flash the iconic Iveco commercial vans directly through the diagnostic port with your AutoTuner Tool . Coverage: Iveco Daily (2.3 & 3.0 HPI/HPT engines) Iveco Massif (3.0 HPI engine) Method: 100% OBD (Normal Read). Plug in, read, write. The perfect solution to tune commercial fleets in record time! Key Features: Type: Engine Control Unit (ECU) Mode: OBD NR Readout: Calibration MCU: MPC562 Read time: 45sec Write time: 1min Checksums correction Compatibility List*: Iveco Models: Daily (2006–2019) / Massif (2008) Iveco Engines: 2.3 HPI / 2.3 HPT / 3.0 HPI / 3.0 HPT *The list may evolve over time. Does it read full flash through the obd? Or only MAPpack? Partial read , same size as full but less data. only 2.3 or the C39 protocol in general? 3.0 or 2.3 , same C39 ECU.

  Problem: Trying to read an Audi Bosch DQ381 gearbox with CG FC200 ecu programmer on bench but failed to connect with this TCU. It says error "E111 Security Authentication Failed", Any solution? Solution: The boot version is bh1g0401. This is generation 2 bootloader 401. You can not read it with fc200. Software too new and fc200 can’t break security, yet. Flex or Autotuner can do it.     

 CGDI released a new DAP adapter that is designed to read both EEPROM and Flash data from Delphi ECUs. Here iecutool.eu will show how to read a Hyundai Delphi DCM7.1AP ECU with CG FC200 programmer and DAP adapter. Select Hyundai- Delphi DCM7.1AP TC277T ECU and choose boot mode. Check wiring diagram. Connection Setup: 5 wires were connected as per the wiring diagram. A stable 12V power supply was provided. The DAP adapter successfully connected to the ECU. ECU Identification The FC200 software displayed the ECU ID and confirmed a successful connection. Reading D-Flash (EEPROM) The adapter read the entire D-Flash memory without errors. Data was saved to a desktop for backup or cloning. Reading P-Flash (Flash Memory) The Flash read process was also completed successfully. The file was saved and verified. Why This Matters? Previously, reading both EEPROM and Flash from Delphi-based ECUs required multiple adapters or complex procedures. The FC200 adapter now p...

  Autotuner new protocol- Bosch MD1CS069 (Agri & LCV): Live on Bench (after Mail-in Unlock)! The professional market is calling! The Bosch MD1CS069 ECU (FPT Euro 6d & Stage V engines) is now supported on your AutoTuner Tool. Massive Coverage: Iveco Daily, Fiat Ducato (2.3 & 3.0 HPI / Multijet) Mitsubishi Fuso Canter New Holland, Case IH, Steyr, Landini tractors Method: Bench (After Mail-in Unlock) . Send the ECU to us to unlock and secure the solution, then flash it via Bench right in your shop! The LCV and Agri sectors are waiting for you. Key Features: Type: Engine Control Unit (ECU) Mode: BENCH NR MCU: TC299 Read time: 1min 45sec Write time: 30sec Checksums correction Backup creation Mail-in Unlock required Compatibility List*: Case Construction Model: 590SV (2022) Case Construction Engine: 3.6L Case IH Models: Farmall (2020–2023) / Farmall A (2021) / Luxxum (2022–2023) / QUANTUM (2018) Case IH Engines: 120 C 3.6l / 90 C 3.6l / 110 X 4.5l / ...

 Read and write Nissan/Infiniti MED17.7.2 ECU with CG FC200 programmer successully. Quick search MED17.7.2 ECU. Use platform mode (bench mode). Check wiring diagram. Connect ECU with FC200 via FC200 ECU adapter. Read Dflash and Pflash ok. Write Dflash and Pflash ok. IMMO OFF ok. Immo off in device without 3rd party device. Images attached:

  XIRDecoder New Support Added! XIRDecoder support for Hyundai–KIA —  MD1CS012 ECU. Supported features: * DTC * DPF * EGR * LAMBDA * MAF * SCR * STAGE1 * TORQUE MONITOR * TVA * VMAX

  Problem: I’m having trouble reading my DL501 gearbox at foxflash programmer . I have to disconnect and re-connect several times, but the reading remains stuck at 0% . Any solution? Solution: You need Bench MFC cable. You need to use multifunction cable that is included in foxflash kit. There is a ignition switch. 12v+ and 12v Ignition. The ignition is under the on/off switch of mfc cable. Pinout directly from device to gearbox doesn’t work. Press read not get id. When tool told you put on or off. After put off, CLICK read then put on After..not before. Tested dl501 gen1 all okay. Even cloning. If use Godiag TCU adapter, before with ECU adapter and have to press the 120ohm button briefly when building the connection then it read immediately. Just try or plug K15 in and out. Example: Audi A6 C7 DL501 Cloning. Read OK Write OK