Posts

Showing posts from October, 2023

Foxflash Renault MD1CS006 Modification Not Allowed in OTP Zone?

Image
  Problem: Foxflash read Renault MD1CS006 ecu ok, but failed to write ecu. Error "Modification is not allowed in virtual OTP Zone". Any solution? Solution: You have modified your file in otp area. The edited file is bad. Change your file supplier, send original file, modify file and rewrite. www.iecutool.com

Foxflash Failed to Read VAG MED17.5.5 via OBD, Bench and Boot?

Image
  Problem: I cannot read Audi A1 1.4tfs MED 17.5.5 with foxflash tool on bench and obd?? I can only identify and write. Failed to read also a seat ibiza 1.4tfsi med 17.5.5 impossible obd boots bench. Possible solutions: If read it via OBD, try to go up to 14 volts normally it should pass. If all methods fail, the ECU is encrypted, foxflash cannot read it directly. Try to update ECU to latest software version with flex and then you can read with foxflash on bench mode. Foxflash bench pinout to VAG MED17.5.5 To read and write use the following driver: → BENCH TRICORE → VW / AUDI / SEAT / SKODA → TC1766 — VAG → MED17.5.5

Can Foxflash Read Siemens EGS52 EGS53 TCU?

Image
 Some users reported that foxflash failed to read Mercedes/Chrysler Siemens EGS52 or EGS53 TCU. They can see it in the menu, but unable to read? Foxflash will read/write EGS52/EGS53 in boot mode if ECU is not encrypted. If you fail to read EGS52/EGS53 in boot mode, make sure you don't connect the bench box during boot operation. Foxflash Siemens EGS52 boot pinout Foxflash Siemens EGS53 boot pinout www.iecutool.com

Foxflash Read Mercedes MED17.7.3.1 ECU on Bench

Image
 User feedback: Mercedes Benz W212 500 V8 with ECU MED17.7.3.1 read/write goes well using foxflash . To read and write use the following driver: → BENCH TRICORE → MERCEDES → TC1797 — MERCEDES → MED17.7.3.1 BOSCH MED17.7.3.1 [ 1797 + EXT.F. ] — Mercedes Benz [Gasoline] pinout

PCMTuner Read KTM 790 Duke Bosch ME 17.9.21.1 Success

Image
PCMTuner new test report from Mr. Katzmarek: KTM 790 Duke 2023 Model Bosch ME 17.9.21.1 read and write successfully with pcmtuner module 71 . Using this pinout

Foxflash VAG MED17.1 OTP Sector Not Writeble?

Image
Problem: New KT200/ Foxflash keeps getting this message when I try to write it to the replacement DME VW MED17.1. When I try to write Ori file on used junkyard ecu I have this error: "uncorrect file 01000 — OTP sector not writeble." Any solution? Solution: The ecu file needs to be cloned OTP's taken from clone file copied to ori file. If you can not write in bench, open the ecu and write in boot mode. Feedback: I use Foxflash with "tricore clone method boot modality" using bench mode and in this way I have obtained a writeable file.

Foxflash Opel Vivaro EDC16 Write "Error Send WakeW"?

Image
  Problem: Read Opel Vivaro EDC16 via obd with foxflash to remove EGR on devinci but wasn't available when tried different software write back in now got no revs. Launch X431 scanner gets injector fault code P0611. Any solution? Solution: Thi model is Renault engine. You lost injector codes. You need to recode them. If the car starts without a problem you need to reset the injector code and also see if the calculator has not lost the serial number.

How to do Foxflash Bench Box Self-Test?

Image
  Question: The foxflash main box work with obd and direct connect bench. But if i used the in some cases if need, the bench box, no have connection. Is there any way to test bench box? Connect the bench box to the foxflash tool and power it through th round jack of the bench box itself or from the round jack of the foxflash tool. Run foxflash manager Select Tools Bench Mode->Test for Bench Boxes->Test Bench Box V2 This driver is useful for testing the Bench box. During the test -the relays will be triggered at different speeds -the red LED will flash several times Press Start Test Bench box self-test finished. If bench box self-test result is fine, but software has no communication, the problem can be the voltage, ecu or wiring connection. https://www.iecutool.com/service/foxflash-bench-box-self-test.html

How to Read Gen2 Mazda3 ECU with PCMFlash + Godiag Adapters?

Image
 PCMTuner dongle (pcmflash 1.2.0) will read Gen2 Mazda3 (2010+) ECU via OBD module 9. If already remove ECU from car, it can be read via OBD on bench mode using Godiag adapters. Tools used: Scanmatik pro2 PCMTuner dongle Godiag GT100+ breakout box Godiag ECU Boot GPT adapter (the adapter can be used with pcmflash + j2534 device to read ECUs in boot, bench or GPT mode) Connect SM2 Pro with laptop and gt100 Connect godiag ECU adapter with gt100 Connect godiag ECU adapter with ECU via jumper cables following the wiring diagram Connect 12v powre supply to gt100 Plug pmctuner dongle to laptop Press the MNL button on the godiag ECU adapter Run pcmflash software (DON'T UPDATE SOFTWARE ONLINE) Select procotol Read ECU Read ECU completely. Save data. www.iecutool.com

How to Read Mercedes Delphi CRD2.16 with Foxflash?

Image
 Question: How to read Mercedes Delphi CRD2.16 ECU with foxflash ? cannot find wiring diagram to this ECU. Solution: Jtag boot read this ecu. Same pinout as Delphi CRD2.10 SOLENOID OBD JTAG_BOOT. Connect the multifunction cable as follows: Solder 3 links on the pcb: Solder the rainbow flat cable on the pcb: To read and write use the following driver: Foxflash team is developing a new adapter for jtag. You can connect the new adapter and read this ECU by OBD.

How to Register/ Login Foxflash on Second Laptop?

Image
  Problem: I installed foxflash tool on one laptop, no problem. Now i want install it to a different laptop and i can not continue. How to log in foxflash on second laptop? Solution: Just use the same email and code (device S/N) as you input on 1st laptop. Read also: http://www.pcmtuner.org/foxflash-ecu-software-installation-guide/

Will Foxflash Read and Write PSA Marelli IAW 6LP?

Image
 PSA Marelli IAW 6LP Is Safe Read and Write with Foxflash on OBD? Foxflash doesn't read it for obd. It will do it in boot mode. If need to read it by OBD, go for ktag. If have foxflash tool, do it like this. PSA Marelli 6LP HW01 MARELLI 6LPx Vers.1 [ ST10F280 / ST10F296 ] — Peugeot, Citroen [Gasoline] Connect multifunction cable and the resistances as shown. To read and write use the following driver: → TOOLS BOOT MODE → ST ST10Fxxx → ST10F280 or ST10F296 PSA Marelli 6LP HW02 MARELLI 6LPx Vers.2 [ ST10F280 / ST10F296 ] — Peugeot, Citroen [Gasoline] Connect multifunction cable and the resistances as shown. To read and write use the following foxflash driver : → TOOLS BOOT MODE → ST ST10Fxxx → ST10F280 or ST10F296 PSA Marelli 6LP HW03 MARELLI 6LPx Vers.3 [ ST10F280 / ST10F296 ] — Peugeot, Citroen [Gasoline] Connect multifunction cable and the resistances as shown To read and write use the following driver: → TOOLS BOOT MODE → ST ST10Fxxx → ST10...

Foxflash Failed to Read MED17.5 by OBD?

Image
  Question: I can't do MED17.5 TC1766 1.5 mb file with foxflash by obd? any solution? Solution: Use bench or boot mode. Bench mode: BOSCH MED17.5 [ 1766 ] — VW, Audi, Seat, Skoda [Gasoline] To read and write use the following driver: → BENCH TRICORE → VW / AUDI / SEAT / SKODA → TC1766 — VAG → MED17.5 Boot mode: BOSCH MED17.5 [ TC1766 INT.F.] — VW, Audi, Seat, Skoda Step 1: Read and Write ECU Connect with the multifunction cable the following pinout and the boot shown below. Use the driver: → TOOLS BOOT MODE → INFINEON TRICORE Boot → SAK TC1766 If the password error message appears at the beginning of the reading, proceed as follows: Step 2: Password search Disable the boot mode by unsoldering the grey wire. Connect the pinout below. Use the foxflash driver : → TOOLS BOOT MODE → INFINEON TRICORE Tool Password → OBD PASSWORD TPROT V08 VAG → Click on "Find Password" and follow the software messages. Now that the password has been found it's possi...

Foxflash Failed to OBD Write Ford SID209 Solution

  Problem: I have a problem with read ecu SID209 from ford transit 2015 i can read flash and password with foxflash by obd but i have an error when i try to write file by obd? Iecutool solution: First read obd password, after that remove ecu and read/write boot mode. 1. Send OBD read data and boot read (full read eeprom/ flash) data to iecutool.com engineer, foxflash team will help modify data, then OBD rewrite. 2. If boot read not working, try to write the OBD read file via OBD on bench mode (using godiag gt100 breakout box), then report the result. Check SID209 boot pinout here http://www.pcmtuner.org/can-foxflash-read-write-ford-sid209/

Foxflash Failed to Read Renault SID306 by OBD?

Image
  Foxflash tool failed to read and write Dacia Duster SID306 ECU via OBD? voltage is 13V+. If fail to read SID306 by OBD, try boot mode. Foxflash SID306 boot pinout SIEMENS CONTINENTAL SID305/SID306 V.1 [ TC1766 INT.F.] — Renault, Nissan Read and Write ECU Connect with the multifunction cable the following pinout and the boot shown below. Use the driver: → TOOLS BOOT MODE → INFINEON TRICORE Boot → SAK TC1766 Below we show 2 alternative methods of booting in the absence of the D48CB02 cable. Some hardware versions only boot in the following way: If OBD and boot all fail, the ECU is encrypted and it is not supported by foxflash. www.iecutool.com