Posts

Showing posts from April, 2023

PCMTuner Honda PGM-FI USB Not Recognized Error Solution

Image
  Problem: When i tried my first laptop to ID Honda Accord ECU as soon it did ID. After they i get USB not recognized error. Then i installed pcmtuner flash software in another laptop. Got every thing activated. Did ID honda eca via OBD. It did identified but again same error computer say USB not recognized. Tried uninstalling and installing UsB drivers still same. Plz check photos for reference Can you help? Solution: Do not plug 12v power into pcmtuner. Also, this work better with tactrix or openport interface. Don't forget to select it in the drop down box in pcm software. Feedback: All done using OpenPort 2.0 with pcmtuner software.

Foxflash Pinout to Mercedes SIEMENS VDO MSM2.0

Image
  Foxflash programmer will read and write Mercedes Benz gasoline SIEMENS VDO MSM2.0 ECU on bench. Here is the fox flash pinout to MSM 2.0. Select driver Mercedes Siemens ECUS 1.4/1.6 Siemends VDO MSM 2.0 FULL SYSTEM If old and new ecu have read flash and eeprom without problem. Write not work with foxflash. Have error. Cannot write any file as shown image below: After read flash/eprom — Disconnect ecu and restart software (unplug foxflash ) — restart Then connect again, Write flash, Also try lower power only need 13v on this ecu.

Foxflash Pinout to FCA Dodge CONTINENTAL GPEC3

Image
 Foxflash recent update adds FCA Dodge CONTINENTAL GPEC3 ECU. Here is the foxflash pinout to CONTINENTAL GPEC3 BAM SPC5674 CONTINENTAL GPEC3 FCA Pinout Connect with the multifunction cable the CNF1 on the pcb. READ AND WRITE ECU Use the driver: → TOOLS BOOT MODE → MOTOROLA FREESCALE BAM → CONTINENTAL GPEC3

Read/Write BMW MSV70 DME by Foxflash, Ktag or FC200?

Image
 Which tool to read this computer BMW MSV70 DME? Foxflash : Yes, via BDM Jtag Connect multifunction cable as follows: Solder the dip/sip connectors on the pcb and do a link: Insert Siemens/Marelli adapter as in photo: To read and write use the following driver: → BDM/ JTAG MODE → BDM MPC → MPC55x/56x Ktag / Kess V2 : Need luck. The best option is BDM. Sometimes Kess v2 and ktag clone read ok but failed during writing, checksum error. Ori Kess done well OBD but takes long. Easy to remove and run in bdm. CG FC200: FC200 programmer does not support this computer.

How to Read Continental CM2150E ECU with Foxflash?

Image
 How to read this ECU Continental CM2150 E on Nissan/DAF using foxflash ecu tool ? You can read CONTINENTAL CM2150E with fox flash by Jtag. Connect the multifunction cable as follows: First, you need to do a bridge in the following way: Solder the rainbow flat cable on the pcb: you need to do your solder points very very very carefully! To read and write use the following driver: -BDM/Jtag -BDM/Jtag Mode -Jtag Nexus MPC/SPC -MPC 55xx When finished, remember to remove the previously welded bridge! www.iecutool.com

Foxflash Simos 18.1 Error Unlock Password Write Solution

Image
  Problem: Hello, I have a problem when writing simos18.1 with foxflash , the ecu is connected in boot. (I am sure it's connected correctly because I checked it over 20 times and was able to read password and then files and do the write all successfully). When I try to write back by doing write all and use the original _all file it writes without any problem. When I write the original separately by either doing eeprom or flash it gives an error saying "error unlock password write 1". Same thing happens when I write modified file back. Solution: Ensure the password file password_adv is located in the Dfb main program folder. Path: \Program Files (x86)\FoxFlash Manager\foxflash\DFB Technology folder. Remove all resistors and boot from ecu, Connect up power+canH+CANL and do a bench OBD get info. then disconnect from ecu..now do bench mode password, read password (delete old password from folder first). then disconnect bench and read flash eprom. Power off ...

PCMTuner Read and Write Mercedes CRD3Plus.A0 via Module 53

Image
 Tried to do CRD3Plus.A0 from Mercedes W205 C220 170hp 2015 Module 53 Infineon TC1797 Mirco 4096KB PCMTuner Read / Write works fine Car starts, but turn off with P060100 checksum error. Tried 2 different Winols Solutions from Tuner. But didn't work. (you must disable checksum correction as the tool cannot do it, must be done manually) After flashing car back to stock, car will run. I took a look, at this guide: https://www.iecutool.com/service/pcmtuner-module-53-tricore-bsl-instruction.html

Foxflash Read and Write VW Passat EDC16U34 via OBD

Image
 VW Passat B6, 2.0 TDI 8V, 140hp EDC16U34 read and write with foxflash tool , all obd. Reading — ~13min Writing — ~3min foxflash will read VAG EDC16U34 on bench as well. To read and write use the following driver: → BENCH MODE → [brand] → MPC561/2 — [brand] → EDC16 U34

Foxflash Read Nissan EDC17C84 by OBD, Bench or Boot?

Image
 Is it possible to read and write EDC17C84 NISSAN MICRA with foxflash via OBD? No, just bench and boot. Read Nissan EDC17C84 with foxflash on bench BOSCH EDC17 C84 [ 1782 ] — Renault, Nissan [Diesel] Connect the multifunction cable as follows To read and write use the following driver: → BENCH TRICORE → RENAULT or NISSAN → TC1782 — RENAULT → EDC17 C84 ATTENTION: Some EDC17C84 enter in Bench mode with the white and brown wires on pins F4 and G4. If with the previous pinout doesn't enter in bench tricore mode, then try again by connecting it as follows: Read Nissan EDC17C84 with fox flash in boot mode BOSCH EDC17 C84 [ TC1782 INT.F.] — Renault, Nissan Step 1: Password search Connect the pinout below with multifunction cable. Use the driver: → TOOLS BOOT MODE → INFINEON TRICORE Tool Password → PASSWORD BFT → Click on "Find Password" and follow the software messages. If the password was found with this system, go directly to the boot step to read and wr...

PCMTuner Failed to Read Kia EDC17CP14 on Bench?

Image
  Problem: Any way to read the edc17cp14 kia with pcmtuner in bench mode with 71 module. I test many ecu but no results. Solution: First edc17cp14 pinout is for Hyundai/Kia. Do not try read until ID successful, need 14v. Tprot must not be TRPOT3 or TPROT11- if so need do OBD. If failed to read it with module 71, then try read by OBD. If it can read by OBD, then ecu TPROT is to high for bench mode. You can do obd it work but takes more than 2 hours. or read by foxflash on bench. foxflash Hyundai Kia EDC17CP14 pinout To read and write use the following driver: → BENCH TRICORE → HYUNDAI / KIA → TC1796 — HYUNDAI KIA → EDC17 CP14

Foxflash EDC17C66 "Error Unlock Password" Solution

Image
  Problem: Mercedes Benz EDC17c66 problem "error unlock password" on bench when writing with foxflash tool . The best is that first time when I was writing file all was ok but when I want second time write same ECU with other file next day, this happened. Solution: The error message "error unlock password" typically indicates that the ECU is locked and requires an unlock code before it can be programmed. This can happen if you have attempted to program the ECU with an incorrect or corrupted file, or if the ECU has been tampered with in some way. There are a few things you can try to resolve this issue: Check that you are using the correct programming tool and software for your ECU. Make sure the tool supports the ECU you are working with and that you have the latest version of the software. Try reading the original file from the ECU and saving it as a backup before attempting to write a new file. This will ensure that you have a working backup in case...

PCMTuner Cannot Identify VAG PCR2.1 on bench?

  Question: Pcmtuner flash can't identify the VAG PCR2.1 ECU. Checked with Flex and ECU Is already unlock,but pcmflash with module 57 and Its pinout can't identify and read. Answer: module 57 is OBD you cannot do on bench! PCMflash does not do OBD on bench — the module is OBD as in ecu must be fitted to car this ecu comms is via vehicle CEM unit and dash board. try BSL mode here: http://www.pcmtuner.org/pcmtuner-vag-simos-pcr2-1-unlock-instruction/ or use foxflash, it will read/unlock pcr2.1 via OBD or bench. http://www.pcmtuner.org/foxflash-unlock-vag-pcr2-1-by-obd/

Foxflash Read and Write BMW EDC17C50 on Bench

Image
 Will foxflash read and write BMW EDC17C50? via OBD or bench? Auto checksum or manually? Yes, Read/Write works 100% on Bench. only bench though, no VR available for these ECUs. checksum is auto on this EDC17c50. You can also do checksum manually. Foxflash BMW EDC17C50 pinout For this ECU there are 3 different types of hardware versions, try the following 3 combinations in series. The ECU will not suffer any damage during connection tests. This pinout work for my ECU Read and write without problem. Checksum by fox flash .

Foxflash Read and Write Mercedes SIM271DE2.0 in Boot

Image
 How to read and write Mercedes Benz SIM271DE2.0 with foxflash ecu programmer in Boot mode? Step 1: Search Password Connect the pinout below with multifunction cable. Use the driver: → TOOLS BOOT MODE → INFINEON TRICORE Tool Password → OBD PASSWORD SIM271 MERCEDES → Click on "Find Password" and follow the software messages. Now that the password has been found it's possible to read and write the control unit. Step 2: Read and Write ECU Connect with the multifunction cable the following pinout and the boot shown below. Use the driver: → TOOLS BOOT MODE → INFINEON TRICORE Boot → SAK TC1796 Tips: Better try CNF1/BOOT connection after read password (not resistor method as pinout above). CNF is at the side of your MFC switch. Boot is just a GND. you only need Boot and green (ignition connected) and must change ecu canbus pins for boot different than password. connect ignition directly to resistor. Review: MERCEDES W204 C180 C200 C250. SIM271DE2.0 READ A...