FoxFlash Read and Write VAG Siemens PPD1.2 by OBD

 VAG Audi Siemens PPD1.2G feedback! Foxflash online reading and writing Audi A3 170 hp PPD1.2G via OBD successfully.

FoxFlash Read and Write VAG Siemens PPD1.2 by OBD

FoxFlash Read and Write VAG Siemens PPD1.2 by OBD

FoxFlash Read and Write VAG Siemens PPD1.2 by OBD

FoxFlash Read and Write VAG Siemens PPD1.2 by OBD

PPD works without Problems over OBD.

These are supported VAG PPD.x list of fox flash.

Audi car A3 2.0l 16V TDI Siemens PPD1
Audi car A4 2.0l 16V TDI Siemens PPD1
Seat car Altea 2.0l 16V TDI Siemens PPD1
Seat car Leon 2.0l 16V TDI Siemens PPD1
Skoda car Octavia 2.0l 16V TDI Siemens PPD1
Volkswagen car Golf V 2.0l 16V TDI Siemens PPD1
Volkswagen car Passat 2.0l 16V TDI Siemens PPD1

Comments

Post a Comment

Popular posts from this blog

FoxFlash Read and Write Volvo Denso MB279700-9xxx

Image
 Foxflash Volvo Denso MB279700–9xxx works perfectly, just follow the steps of foxflash , reading, unlocking, and writing all done on the bench. PROCEDURE: 1 — Read the Ecu AND unlock the Ecu 2 — Write the ECU READING AND UNLOCKING: Connect the following pinout using the multifunction cable. Start the driver: CAR > VOLVO > TOOLS VOLVO >UNLOCK DENSO MB279700 9641 SH72546R CAN Click on the READ FILE button to read the file. After reading, click on the UNLOCK button to unlock and enable the writing of the control unit. WRITING: Now it will be possible to reconnect the control unit to the car and write the modified file via OBD. Use the following driver: CAR > VOLVO > Model >2.0 DENSO MB279700 9641 SH72546R CAN Alternatively, you can WRITE also the ECU on the table using the pinout on the next page. Note: Compared to the read pinout, the CAN line is moved. FOXFLASH PINOUT FOR WRITING: Just follow the foxflash instructions: read file 15 min, unlock
Read more

Read/Write BMW MSV70 DME by Foxflash, Ktag or FC200?

Image
 Which tool to read this computer BMW MSV70 DME? Foxflash : Yes, via BDM Jtag Connect multifunction cable as follows: Solder the dip/sip connectors on the pcb and do a link: Insert Siemens/Marelli adapter as in photo: To read and write use the following driver: → BDM/ JTAG MODE → BDM MPC → MPC55x/56x Ktag / Kess V2 : Need luck. The best option is BDM. Sometimes Kess v2 and ktag clone read ok but failed during writing, checksum error. Ori Kess done well OBD but takes long. Easy to remove and run in bdm. CG FC200: FC200 programmer does not support this computer.
Read more

PCMTuner PSA Bosch MED17.4 Pinout

Image
 I'm trying to read one Bosch MED17.4 from a Peugeot 207 1.6t; ecu pinout is correct, but pcmtuner pcmflash shows failure, I'm using module 71 tc1766 FLASH… So, any clue? Solution: There are 2 types of pinout for med17.4. Try both. see which one works. Bosch MEDV174 IROM TC1766 EGPT PSA Pinout Feedback: Solved. Mine work with type 1 and module 71 TC1766.
Read more