PCMtuner-tool

 Foxflash user new feedback: Audi Q7 4.2 FSI — ECU MED9.1.1 Successfully pinout connection for MED9.1 not for MED9.1.1!!! Read on bench. Write on bench. Checksum with foxflash . Stage 1 all ok. Foxflash Audi MED9.1 MPC563/4 ECU bench pinout FYI: Here is the bench pinout for Audi MED9.1.1 MPC563/4 ECU. www.iecutool.eu

 Foxflash user feedback: Aprilia Dorsoduro 750 motorcycle immo off with Foxflash successfully. Read and write via OBD. How to read this ecu with foxflash ? Buy adapter Fiat 4 pin to OBD. And read write by OBD. You can make the Ecu Immo off. But this is not going to solve dash issues! Like security code bypass for the dash. You can make only ecu immo off. After that you have to change the eeprom in the dash. And then you can enter a code in the dash. And start the bike without a transponder.

  User review: Iveco Euro cargo 2013 Bosch EDC7UC31 First truck. Read ok, write ok, checksum by foxflash . Bench mode. Also tested 1. EDC7UC31 IVECO STRALIS Read/Write/Checksum OK ADBLUE OFF 2. Iveco Trekker 410 Read/write/checksum EDC7UC31 Foxflash bench pinout to Iveco truck EDC7UC31 To read and write use the following driver: → BENCH MODE → Iveco → MPC561 — Iveco → EDC7 UC31 www.iecutool.eu

  Problem: I need to write immo off data on DSG DQ250 MQB using foxflash programmer. I can read Backup, flash, EEPROM. I can write Backup, immo off flash I can’t write only eeprom, immo off EEPROM. Any solution? Here is the clue. DQ250 MQB has two EEPROM Int EEPROM & ext EEPROM. No solution with Foxflash. Foxflash can’t Read &Write ext EEPROM. You will need other tools, Flex, Autotuner, Launch X-prog3 or Launch ecu programmer etc.

 Although the OBDStar dc706 doesn’t show the Dodge Ram being supported it does work to read and write internal flash and eeprom. The ram Pinout shows the can wires in a different place and only reads with Hp Tuners in the pinout it’s original hooked up in. However if you switch the can wires and add the gpt wires you’re able to use the OBDStar dc706 to read/ write these ecm’s and effectively clone them along with altering vin numbers. You can see this pinout. Here got the CAN Wires positive, negative. We all know the OBDSTAR supposedly will only read and write the Jeep. There is no pinout for Dodge like we have on the HPTuner. We’re just going to leave this pinout. Then hook up our OBDSTAR DC706 ecu programmer . We have this hooked up same ECM. We switched our CAN wires to a different pin. We’re using this exact pinout right there. We’ve switched an alltime positive to an ignition there. You can read the internal Flash and you can write both of those. If you wan...

 Reading BMW Bosch EDC17C50 ECU with foxflash on bench. But it kept stopping at 44% when writing file on bench using clone function (Built-in function). Opened it and worked right away in boot mode. All ok. Cloned ecu successfully. Password BFT read. 15 minutes write. When you clone the Bosch ECU you have to look at what it says EEPROM PROTECT, then bench blocks the ECU, it has to be because of boot.

 How to read Audi Q8 MD1CP001 ECU using Launch x-prog3 PC adapter ? It is a easy task with Launch x-prog3. Run X-PROG3 PC software, select Audi- Q8 2018–2019- MDCP004 SPC5777. Check wiring diagram The connection is easy. Connect ECU with x-prog3 and PC adapter . Connect with ECU. Then read/save eeprom and flash data respectively. X-prog3 also corrects checksum for MD1 ECU. www.iecutool.eu