PCMtuner-tool

 With OBDSTAR DC706 , users can read eeprom and flash on a 2011 VW jetta ME17.5.6 ECU, then use the immo decoder function to get the CS and PIN code from the ECU. Immo data decryption give you the pin and CS. Read eeprom and flash, then hit immo data calculation. then it gives you CS, pin and MAC. It also reads immo data, so you can load that in your key programmer and make a dealer key with the CS and PIN. Much easier to do AKL this way than pulling the cluster. It is a hell of a lot easier than pulling the cluster. key work with 00 7th byte CS. then manually programmed remote. www.iecutool.eu

  Problem: How to solve this problem. after installing new Foxflash version 1.4.2 on windows 7? Error "Unable to Check Server". I always use Windows 7, this happened after the update. Solution: This message will appear on Win7 system. On Win10 it does not appear. Some use it on Windows 7, getting this message for a few days, but FoxFlash will load without a problem. Try running it without pressing OK. I f it doesn’t work, restart the computer and try again despite this message. After a few days this message didn’t come out again and it still works well with the latest version 1.4.2 of FoxFlash. We strongly recommend installing foxflash software on Win10 or Win11 systems. www.iecutool.eu

  Foxflash read and write Iveco STRALIS EDC17CV41 ECU on bench successfully. To read and write use the following driver: → BENCH MODE → Iveco → TC1797 — Iveco → EDC17 CV41 Read ok, write ok Checksum by foxflash. EGR + DPF off. Check pinout here http://www.pcmtuner.org/edc17cv41-pinouts-to-pcmtuner-and-foxflash/

 Audi A6 2.0l tdi 2010 Possible to read and write with foxflash via obd? Tried to read via OBD but failed. It is written, bench or boot mode. 2010 has Tprot. Only bench mode to bypassing tprot. Bench write and read ok. Check bench pinout here http://www.pcmtuner.org/foxflash-read-and-write-audi-a4-2-0-edc17cp14-ecu/

Foxflash read and write Mazda CX-5 Denso ECU SH1K via OBD successfully. OBD Read/Write worked fine. Photos added. Read time takes 30 minutes. But it works. Select ->OBD driver ->Mazda ->Mazda CX-5 ->2.2 SKYACTIV-D Denso SH1X *CAN Voltage 14V. EGR Off.

 It is a Ford Transit Visteon with DCU101 ECU. Foxflash will read and write this ECU via OBD. It is DCU 101 but protocol DCU 102/108 works. Select OBD drive ->Ford ->Transit ->2.2/2.4 TDCI E4 FOMOCO VISTEON DCU 102/108 *CAN Read ok via OBD. Write OK via OBD. Checksum by foxflash. EGR + DPF OFF. www.iecutool.eu

  FormulaFlash released new software 1.0.0.7 on October 21st, 2024. 1. Adds ME788 BSL mode, read, write, clone, checksum and IMMO Off, idle speed adjustment, power upgrade (World’s first) 2. New checksum: Simos 8.x, MSD80, MSD81, MSD85, MSD87 Upcoming updates: 1. ME7.8, ME797, ME7971 virtual reading and writing, checksum, one-click operation mode for immo off, idle speed adjustment, power upgrade (World’s first) 2. ME797, ME7971 BSL read, write, clone and checksum 3. EDC16, EDC17, MED9 DTC clean and idle speed adjustment solution www.iecutool.eu

  Problem: Successfully read and write Audi Bosch Md1cs004 ECU with Foxflash . SCR off. But scanner shows fault code U2A200 after scr off. Reductant quality sensor no communication. How to fix it? Solution: Just disconnect adblue pump. Disconnect adblue if the fault doesn’t disappear do dtc off solution as well. User feedback: Unplugged Scr unit. Dtc gone. But new in gateway instead for scr.. coded scr out with autel in gateway. Now no issue. www.iecutool.eu

 It is a Yamaha MT 07 2021 with R5F10DMFJ chip. How to read/write this massive chip? What tool can be used? Here is the clue. UPA 1.3 cannot read, you need pogrammer for this mcu smok, xtool, carprotool, CG100/ CG100X , vvdi prog ect Here is the pinout wiring connection. Feedback: I finally bought a CG100x from iecutool.ru . I’ve just made on the soldering points. successfully calculate km to 5000. Thanks so much for your help.

 Landrover Freelander2 CEM successfully cloned by OBDSTAR DC706 programmer. Delphi CEM M30882F+ 95320 DC706 clone this CEM on bench mode using P004 adapter. Read EXT eeprom 95320 Read EXI eeprom decrypted Read INT flash M30882F Read configuration zone Write EXT eeprom 95320 Write EXI eeprom decrypted Write INT flash M30882F Write configuration zone Car starts no problem. www.iecutool.eu

  Problem: Foxflash read and write Audi MED9.1 via OBD successfully. But after flash and 5 or 6 starts, unable to start. Any solution? Possible reason: Checksum problem. Solution: Modify checksum manually. FYI: Better do it on bench mode cause this ECU is not easy to find. Bench mode is safer. check pinout here http://www.pcmtuner.org/foxflash-read-vw-med9-1-ecu-on-bench/ User feedback: Bad checksum, modified checksum with winols and work perfectly. www.iecutool.eu

 Read and write Bosch ME9.7 by Alientech KESS3 successfully. It is a Mercedes S500 V221 with Bosch ME9.7 ECU. Function: Identify ECU Clone ECU Read backup Write backup Reading Micro, Flash and Eeprom Writing Micro, Flash and Eeprom

 Question: Looking for a solution to unlock a Volvo 48v battery after had a crash. Lithium battery from a Volvo mild hybrid car who has had a crash and need to reset crash memory from battery BMS. Had fault code B1652–7F or B1627F. What tool will do Volvo mvbm 48v battery crash reset? There are several tool that will read and write Volvo MVBM 48V battery module eeprom to clear crash. 1. CG100X CG100X will read and write this module on bench. 2. Autel IM608 XP400 Pro Crash in eeprom. Autel can read and write it. 3. OBDSTAR Odometer or X300 Classic G3 OBDSTAR add Volvo 48V MVBM Medium Voltage Battery Module erase crash records. 4. Try with Smok.

 Possible to read and write MRD 1.40 ECU with foxflash ? Yes, bench mode. List does not have mrd1.40. No worries, just did MRD1.41 with the Foxflash on bench with no problems. Even it is not listed there — just select MRD1 and have a good 4AMP power supply 14Volts. Foxflash bench pinout to MRD1.40 To read and write use the following driver: → BENCH MODE → MERCEDES → SPC5777 — MERCEDES → MRD1

  Problem: Trying to read and write Simos 8.5 ECU with FormulaFlash programmer on bench mode, it failed me and said the slave computer was not connected. Any solution? Solution: Software issue. Software version is too old. Download and update formulaFlash software to latest version, then try again. It should be fine. https://formulaflash.com/pages/software-download

  Question: Trying to read fiat doblo 1.6 diesel with foxflash but failed via obd and there’s no Pinout for this model. Anyone know if it’s possible to read / write with foxflash ? Solution: You can read your ecu on bench mode. there are 4 possibilities, tried them in order. Foxflash Fiat EDC17C49 Bench pinout To read and write use the following driver: → BENCH MODE → [ brand ] → TC1797 — FCA → EDC17 C49 BOSCH EDC17 C49 [ 1797 ] — Fiat, Alfa Romeo, Lancia [Diesel] Version 1: Version 2: If it does not enter bench mode, add ground to pin 44: Version 3: On some EDC17C49 FCA the CAN line is shifted. If with the previous pinout doesn’t enter in bench mode, then try again by connecting it as follows: Version 4: Attention: If it does not enter bench mode, add ground to pin 44: Bench mode is preferred. If you want boot mode, check pinout below. Foxflash Fiat EDC17C49 Boot Pinout BOSCH EDC17 C49, EDC17 C79 [ TC1797 INT.F.] — Fiat, Alfa Romeo, Lan...

  Question: I tried to read Ford Focus 2010 euro 4 edc16c34 with foxflash via obd. It says ‘Danger blocking in writing’. Will foxflash do this ecu via OBD? Here is the clue. Bench is the best. Pcm flash original read/write full bench edc16. Never have any problems with it. Foxflash also good for edc16 bench. Ford edc16c34 up to 2008 ok obd with a lot of tools if you follow instructions, 2008–2010 bench only. It’s same issue with all tools on market. There are 2 C34 versions: hw C34–2x and C34–5x. If it’s 5x, it have another type of flash inside, and you need to bench/bdm it. Feedback: Focus 2010 euro 4 (as euro 5 is sid807evo) tested almost all cheap tools obd, reads ok, writes up to 100% but it fails to wake up ecu from programming mode (some thing like that). Writes back ori file good. bench is best, foxflash obd was tested just for education only. www.iecutool.eu

  FormulaFlash software 1.0.0.6 adds GM Deleco E83 ECM bench mode IMMO Off by one-click. iECUtool.eu here shows how to do E83 IMMO OFF. Quick search E83 ECM and select vehicle model and year. Choose Bench mode Check wiring diagram Connect formulaflash with E83 ECM following diagram Connect ECU. Fisrt read and save FLASH. Then hit IMMO OFF and press Yes. IMMO OFF in progress. IMMO OFF successfully. Press YES to write data to the ECU. Write IMMO OFF data to ECM successfully. FormulaFlash will read Delco E83 ECM via OBD as well. But only bench mode will do one-click IMMO OFF. www.iecutool.eu