PCMtuner-tool

 Question: I want to read and write a BMS module from Smart 451 EV. Is it possible with foxflash ? Answer: Foxflash programmer will read and write Smart EV BMS T1 module on bench. BOSCH BMS T1 [ 1797 ] — SMART EV [ BMS ] Connect the multifunction cable as follows, use the Bench Box: To read and write use the following driver: → BENCH TRICORE → SMART → TC1797 — SMART → BMS T1 ECU tool recommendation: PCMtuner https://www.iecutool.com/wholesale/pcmtuner-ecu-programmer-tool.html

  Problem: Mercedes CDR2 foxflash reading performed OBD. Writing presents an error and presents a message to contact support. what is the solution? Solution 1: CRD2.10 etc is problematic with OBD, you can do JTAG. DELPHI CRD2.10 Solenoid — MPC5566 pinout to foxflash Connect the multifunction cable as follows: Solder 3 links on the pcb Solder the rainbow flat cable on the pcb: To read and write use the following driver: Solution 2: Write with kess v2 will work without problems at this ecu. Read also: http://www.pcmtuner.org/foxflash-mercedes-delphi-crd-2-20-not-start-solution/

  PCMTuner new user report: Read and Write Dacia Lodgy 2017 SID310 via OBD successfully. "Dacia lodgy 1,5dci 2017 110cv SID310 module 59 reading/writing stage 1 -> OBD Checksum ok by pcm tuner. I've done quite a few cars with this tool. Ain't had no issue at all." Image attached: ECU tool recommendation: PCMtuner https://www.iecutool.com/wholesale/pcmtuner-ecu-programmer-tool.html

  Problem: I'm reading Ford SID208 with foxflash via obd but communication failed. Is this not possible via obd? Or i have to open ecu to read it? Its Ford ranger 3.2L 2018. Solution: Silent key is Locked ECU by immobilser. You need to do ecu boot Tricore. Fox flash read and write Ford SID208 in boot mode. SIEMENS CONTINENTAL SID208 [ TC1797 INT.F.] — Ford Step 1: Read and Write ECU Connect with the multifunction cable the following pinout and the boot shown below Use the driver: → TOOLS BOOT MODE → INFINEON TRICORE Boot → SAK TC1797 ATTENTION: If the password error message appears at the beginning of the reading, proceed as follows: Step 2: Password Search Disable boot mode by removing all connections on the pcb. Connect the pinout below (red wire +12V instead of green igniction). Use the driver: → TOOLS BOOT MODE → INFINEON TRICORE Tool Password → OBD PASSWORD SID208 FORD — LAND ROVER → Click on "Find Password" and follow the software messages. At...

  Problem: My foxflash software is not working on Win7 32bit, network connection is fine. Error unable to connect server and insufficient memory. Any advice? Solution: Win7 missing patch for foxflash. Better install software on Windows 10 64bit system. Also make sure your computer has 4GB+ RAM storage. If got this error when installing foxflash manager, change system to Win10 as well. ECU tool recommendation: PCMtuner https://www.iecutool.com/wholesale/pcmtuner-ecu-programmer-tool.html

  Question: Temic full system Mercedes foxflash gives the id but no longer reads the ECU. Any advice? Solution: DON'T CONNECT BENCH BOX WHEN READ THIS ECU. ECU tool recommendation: PCMtuner https://www.iecutool.com/wholesale/pcmtuner-ecu-programmer-tool.html

  Foxflash ecu programmer released new update-adding Bench/Boot protocol for Isuzu EDC17C83. May 23, 2023 update May can't get any better as we release a new exclusive protocol today! In this update, you'll find the BENCH protocol for Isuzu EDC17C83. Supported Control Units & Vehicles ECU: Bosch EDC17C83 TC1793 Supported Vehicles: Isuzu Dmax 2017–2022 1.9D 164cv Isuzu Dmax Rodeo 2017–2022 1.9D 164cv Isuzu M21 2017–2022 1.9D 123cv BENCH read is real. R/W time: ~6 minutes at first programming, then ~ 30s. ATTENTION: Some of the latest vehicles might have a secure gateway. Update method: Run the foxFlash Manager software, and click the download button till all is done. Foxflash pinout to BOSCH EDC17 C83 [ 1793 ] — Isuzu [Diesel] Bench Mode To read and write use the following driver: → BENCH TRICORE → ISUZU → TC1793 — ISUZU → EDC17 C83 Foxflash Boot Mode Pinout to BOSCH EDC17 C83 [ TC1793 INT.F.] — Isuzu Read and write ECU Connect with the multifun...

  Problem: Foxflash read MSV70 E60 523i via OBD, wrote mod, but failed. tried to write ori again, gets stuck at 93% anyone had this issue? Solution: Voltage looks low, write at least 13.8v. If still failed to write mod file, only if Mod file bad, you will need to Write original file in BDM. Foxflash Pinout to Siemens MSV70 Solder the dip/sip connectors on the pcb and do a link: To read and write use the following driver: → BDM/ JTAG MODE → BDM MPC → MPC55x/56x ECU tool recommendation: PCMtuner https://www.iecutool.com/wholesale/pcmtuner-ecu-programmer-tool.html

 Possible to read eeprom/flash data of Mercedes Benz CRD3.40 ECU with pcmtuner ? Yes, via module 52 BSL mode. pcmtuner pinout for delphi crd3.4 in bsl Direct Connection BOOT & CNF1 CONNECTION Connect the BLUE and GREY wires of the cable F32GN037C as shown here below: WARNING If instead of the 14-pin component, used for CNF1 signal, it is present a 8 pins component, the CNF1 connection must NOT be carried out, it is necessary the BOOT connections ONLY. Check: pcmtuner module 53 BSL instruction Flex and Foxflash can do it on bench but if written wrong file and do it in boot. If you cannot do in BSL then not possible to recover eeprom/flash. ECU tool recommendation: PCMtuner https://www.iecutool.com/wholesale/pcmtuner-ecu-programmer-tool.html

 Jaguar XE 2.0d 2017 MEDC17.9 read and write successfully by foxflash ecu programmer, checksum by foxflash. DPF OFF , EGR OFF , ADBLUE OFF. Foxflash pinout to BOSCH MEDC17.9 [ 1793 ] — Jaguar Connect the multifunction cable as follows: Attention: Some MEDC17.9 enter in Bench mode with another CAN line. If with the previous pinout doesn't go in bench tricore mode, then try again by connecting it as follows: To read and write use the following driver: → BENCH TRICORE → JAGUAR → TC1793 — JAGUAR → MEDC17.9 Read ok Write ok, checksum by tool ECU tool recommendation: PCMtuner https://www.iecutool.com/wholesale/pcmtuner-ecu-programmer-tool.html