PCMtuner-tool

  Foxflash read Mercedes Vito Delphi CRD 2.20 ID via OBD ok, but had writing error and van won't start. Jtag is needed? Solution: That protocol is not 100% working via OBD. Reading works but writing gives problems on CRD2.xx. Write original file with Kess v2 clone will do. Choose "recovery" without ID. You can easily read it by Kess obd even of clone. Updated: Kess v2 fixed it wrote in recovery and starts no issues. Do with kess select recovery original file rewrite and everything will be fine and success to me!! Recovery select file read before wait almost two minutes then start writing file.

  Problem: I have problems starting the foxflash software every time it displays and impossible to change the language and work with it am I the only one? Solution: Foxflash tool must be connected and powered, device driver must be installed correctly (check windows device manager), Windows time auto sync must be off, Foxflash manager app must be open and active to use tool. 1 Shutdown date and time automatically syncs 2: shutdown defender 3: shutdown antivirus system 4: run foxflash manger click Active button 5: keep manager running 6: run foxflash manager Then you will be able to change language and select driver. The procedure is the same as new kt200 programmer.

  Foxflash ecu programmer released a new update on February 23rd, 2023. Protocols for Porsche PDK February 25, 2023 You can easy read & write Porsche PDK gearbox now! SUPPORTED CONTROL UNITS & VEHICLES BOOT Porsche 911.2 Siemens PDK4000 Porsche 918 Siemens PDK3000 Porsche 918 Siemens PDK4000 Porsche Boxster 718 Siemens PDK3000 Porsche Boxster 981 Siemens PDK4000 Porsche Carrera 991 Siemens PDK3000 Porsche Carrera 991 Siemens PDK4000 Porsche Cayman Siemens PDK4000 Porsche Macan Siemens PDK3000 Porsche Macan Siemens PDK4000 Porsche Panamera Siemens PDK3000 Porsche Panamera Siemens PDK4000 Reading & Writing Time Read: 12 minutes and 36 seconds Write: 6 minutes and 18 seconds update method: run the foxFlash manager, click the download button till everything done. How to update Foxflash software? run the foxFlash manager, click the download button till everything done.

  Problem: I have a problem with pcmtuner flash . I can read but can't write EDC17c84 via OBD. Solution: Remove ecu and read/write again on bench module 71. If car not start by module 71 bench mode, the problem can be the checksum. After fixing checksums, it works on bench module 71. If not working, try unplug T° engine sensor and try if not succes Wait until T°10 and retry.

  Problem: How to solve this please? After installation and activation of both pcmtuner and pcmtuner flash (a new tool). I have no response when trying to open pcm flash. Error process has exited. Solution: Reinstall with no antivirus and firewall, try open PCMtuner flash directly, you will also get this error IF the ecu is not supported or linked from your pcmtuner app. If it's windows 10 the real-time antivirus is activated every time you restart the system.

 Possible to read and write Ford Continental EMS2511 ECU with foxflash ? by OBD or Bench? Yes, fox flash ecu programmer will read EMS2511 via OBD, bench and boot mode. OBD Mode: OK Ford Focus 1.5T 180ch ECU: Continental EMS2511 Conversion Flexfuel OBD Reading OBD Writing Checksum Fox Flash. Start up ok Bench Mode: OK bench read ok bench write ok Checksum by fox flash bench pinout to Ford EMS2511 Boot Mode: OK CONTINENTAL EMS2511 [ TC1791 INT.F.] — Ford READ AND WRITE ECU Connect with the multifunction cable the following pinout and the boot shown below Use the driver: → TOOLS BOOT MODE → INFINEON TRICORE Boot → SAK TC1791 Also solder the grey wire to the other side of the ecu, see pciture below.

 Possible to read and write Opel ACDELCO E87 ECU with foxflash ecu programmer ? Yes, OBD and bench work fine. OBD OK: Opel Atra j ACDELCO E87 Dpf egr off ,Read and write ok via obd. Bench Mode: OK Opel full system delco e87 Read/write ok Checksum by foxflash ok, voltage 13.5v car starts. If have a problem with full backup, error wrong file size, individually upload without a problem and do a reset, it will work. fox flash delco e87 bench pinout Read/write ok

 VW POLO 2013 ECU PCR 2.1 unlock with foxflash ecu programmer in 3 minutes. Read and write ok, checksum manually with winols. I know foxflash will obd unlock and read file in 10s. I love bench because I can read ALL, in case something goes wrong I have a complete copy. I want a backup copy for any eventuality, OBD you only have INT FLASH. To unlock the ecu, you have to rewrite the eeprom. 90% PCR 2.1 unlocking made me buy fox flash, I had scanmatik+pcm flash but it didn't have pcr 2.1 bench. foxflash software also asks to check checksum, you give it yes or no as you think, I gave no precisely because I did it manually in winols so eeprom copies, then you give it eeprom writing WITH THE TAB YOU COPIED INITIALLY, at a given moment of the question IF YOU WANT TO UNLOCK EPP, give ok and that's it.

  Foxflash ecu programmer successfully read and write 2016 Range Rover Evoque 2.0 ED4 MEDC 17.9 ECU. It is fine on bench, but cannot do Flexray ECU's 2017 onwards. Connect the multifunction cable as follows: BOSCH MEDC17.9 [ 1793 ] — Land Rover [Diesel] pinout To read and write use the following driver: → BENCH TRICORE → LAND ROVER → TC1793 — LAND ROVER → MEDC17.9 Some MEDC17.9 enter in Bench mode with another CAN line. If with the previous pinout doesn't go in bench tricore mode, then try again by connecting it as follows: Bench Read OK Bench Write OK Checksum Tool OK

 Can foxflash ecu programmer read and write Mazda CX 5 2015/2016 denso ECU? What is the read/write method? Bench Mode Bench mode pinout To read and write this ECU, select driver in foxflash software -Bench Mode -Mazda -SH72543-Mazda -Denso SH1 If failed to read ecu on bench, the ecu pinout may be different on this ecu. Try OBD method. OBD Mode: Foxflash OBD worked 100%. manually calculated checksum

 I wonder whether foxflash can read and write a Valeo V50.1 with the V50 protocol on a 2019 Renault Clio 4 0.9tce 90hp. Because available list says that there is Valeo v50, I did a test and report feedback here. Read and write with the Clio 4 0.9tce valeo V50 module on a clio 5 0.9tce with a Valeo V50.1 successfully! Read and write for 4 minutes. Checksum by fox flash tool flexfuel E85.

Foxflash ecu programmer read and write Ford MD1CS005 ECU, checksum correction ok, done on bench. foxflash bench pinout to MD1CS005 Connect the multifunction cable as follows: Use Laboratory power supply or battery To read and write use the following driver: → BENCH MODE → FORD → TC298 — FORD → MD1CS005 Read, write and checksum by the fox flash tool.

 Hyundai/Kia Delphi MT86 with TC1766 read and write is done using foxflash / new kt200 ecu programmer. How to Read and Write DELPHI MT86 [ TC1766 INT.F.] — Hyundai, Kia Step 1: Read and Write ECU Connect with the multifunction cable the following pinout and the boot shown below. Use the driver: → TOOLS BOOT MODE → INFINEON TRICORE Boot → SAK TC1766 First, lift the pin shown: Follow on next page.. ATTENTION: If the password error message appears at the beginning of the reading, proceed as follows: Step 2: Search Password Disable the boot mode by unsoldering the resistances. Connect the pinout below. Use the driver in foxflash software : → TOOLS BOOT MODE → INFINEON TRICORE Tool Password → OBD PASSWORD TPROT V11 KIA — HYUNDAI → Click on "Find Password" and follow the software messages.