Super MB PRO N3 User Guide: Network Set UP and Firmware Upgrade

 Super MB PRO N3 (BMW ICOM A3) can work with all BMW inspection software to perform diagnosis, programming, coding for BMW/ mini/ Rolls-Royce/ BMW Motorcycle (click here to review). This post will mainly introduce how to setup network via USB cable & WiFi for work, and upgrade firmware.

  • Connect Super MB Pro N3 and computer network via WiFi

      • When you connect with WiFi, there is no need to set up the IP address. You need to input the password for the first time using WiFi.

      Select one available WiFi with a good signal to connect

      Super MB PRO N3 configure network and upgrade firmware

      After connection, the active service will show the related device's free state in ITOOL RADAR program and BMW software

      Open BMW software to perform the function supported

      Select Device ID and set up a connection

      Super MB PRO N3 configure network and upgrade firmware

      It starts to identify the vehicle

      After that, the related device will show reserved in ITOOL RADAR program and BMW software at the same time.

      Super MB PRO N3 configure network and upgrade firmware

      Super MB PRO N3 configure network and upgrade firmware

    1. Connect Super MB PRO N3 and computer network via USB cable

        2. When you use the USB cable to connect BMW ICOM A3 and the computer, the IP need to be set up is 192.168.92xx (it's the driver IP address recognized by the device, not the local Ethernet IP address of the computer)

        Right-click Local Area Connection

        Super MB PRO N3 configure network and upgrade firmware

        Click property>> Internet Protocol version 4 (TCP/IPv4)

        Super MB PRO N3 configure network and upgrade firmware

        Input your driver's IP address

        Click OK to connect to the internet

        Super MB PRO N3 configure network and upgrade firmware

        Then you can run BMW software to perform the function supported.

        Super MB PRO N3 configure network and upgrade firmware

      1. Update Super MB Pro N3 firmware

          2. Make sure the BMW ICOM A3 diagnostic tool has been connected to computer network

          Use Google Chrome or Edge to visit http://192.168.92.38:60080

          Click Update Firmware

          Log in with the user name (root) and password (NZY11502)

          Super MB PRO N3 configure network and upgrade firmware

          Click Browse to select ICOM-Bootimage BIN file and click send the file

          Super MB PRO N3 configure network and upgrade firmware

          Confirm to write the image file to the flash

          Super MB PRO N3 configure network and upgrade firmware

          After the system image update successfully, click Update Firmware to back to last page

          Super MB PRO N3 configure network and upgrade firmware

          And select and ICOM-applicationimage BIN file to update

          All updates done, click reboot the device to activate the new image

          Super MB PRO N3 configure network and upgrade firmware

          Done!

          www.obdexpress.co.uk

          Comments

          Post a Comment

          Popular posts from this blog

          PCMTuner Unlock Audi SIMOS 8.6 in BSL Mode

          Image
           SIMOS 8.6 requires unlocking in BSL mode by the appropriate module. BSL is usually boot mode for unlock. Same as PCR2.1 . Example: Audi A7 2012 2.8 fsi simos 8.6 unlock, after read/write simos8.6 with pcmtuner successfully. all resistor 1 kom How to work with blocks that require unlocking (PCR2.1, SIMOS8.6): 1) Check the current lock status in the car, if the check is disabled, you can go to read-write, otherwise follow the instructions 2) Remove the unit from the car, open it, transfer the processor to BSL mode using the connection below (PCR2.1, SIMOS8.6), the work as a whole as in the package 53 (you can use tools like powerbox, and you can do without them) SIMOS8.6 Unlock pcmtuner pinout Red — +12, Black — GND, Yellow — CAN-HIGH, Blue — CAN-LOW 3) Choose "SIMOS8.6 (EEPROM/UNLOCK/BSL) or PCR2.1 (EEPROM/UNLOCK/BSL)" depending of ECU type 4) Click Identification — save ECU data somewhere in a text file. 5) Click Read — save the EEPROM 6) Given that EC...
          Read more

          FoxFlash Read and Write Volvo Denso MB279700-9xxx

          Image
           Foxflash Volvo Denso MB279700–9xxx works perfectly, just follow the steps of foxflash , reading, unlocking, and writing all done on the bench. PROCEDURE: 1 — Read the Ecu AND unlock the Ecu 2 — Write the ECU READING AND UNLOCKING: Connect the following pinout using the multifunction cable. Start the driver: CAR > VOLVO > TOOLS VOLVO >UNLOCK DENSO MB279700 9641 SH72546R CAN Click on the READ FILE button to read the file. After reading, click on the UNLOCK button to unlock and enable the writing of the control unit. WRITING: Now it will be possible to reconnect the control unit to the car and write the modified file via OBD. Use the following driver: CAR > VOLVO > Model >2.0 DENSO MB279700 9641 SH72546R CAN Alternatively, you can WRITE also the ECU on the table using the pinout on the next page. Note: Compared to the read pinout, the CAN line is moved. FOXFLASH PINOUT FOR WRITING: Just follow the foxflash instructions: read file 15 min, unl...
          Read more

          How to Find Bosch ECU Serial Numbers and Correct Pinouts

          Image
           Here is basic post for people asking basic questions, apparently now on high demand since we have gathered again new members in our ECU group . So you got bosch ecu in hand from car and how to figure out how to identify it and what pinout to use? On this case we can randomly take one bosch ecu that we will identify. So all bosch ecus start with serial numbers 028… 026. We just head to bosches page next https://www.bosch-repair-service.com/ Here you search by oe or bosch number, i have random bosch ecu here and it’s 0 281 014 544 and bosch page ends up with a result. We can see its edc16cp35. Now there are two ways. Either to search in foxflash bmw / edc16cp35 for pinout. Or we head to ecu pinout page and figure out pinout from there. One of the best online pinout catalogs can be found at ecu desing, So save webpage https://ecu.design/ecu-pinout/ Copy address and head out there. Type in edc16cp35, bmw uses two processors in this one mpc 562 and mpc564. Pinouts jus...
          Read more