PCMtuner-tool

 Audi A5 2.0 177bhp ECU EDC17C46. Read and write fine with pcmtuner dongle on bench. Module 71. ECU info. Bosch EDC17C46–2.22 0281018128 VAG using sm2 pro with pcmtuner dongle and bench power supply. NOTE: If pcmtuner failed to read this ecu, after transistors replacement, it works perfectly.

  Problem: I tried to read Audi Simos 12 ECU with foxflash via obd, but failed. fox says virtual file not present in database. Solution: foxflash cannot read simos 12 via obd if there is no file in server. Foxflash engineer will upload vr file to server once it is available. You can read and write in boot mode. SIEMENS SIMOS 12 [ TC1797 INT.F.] — VW, Audi, Seat, Skoda Boot Mode pinout to foxflash ecu tool . Step 1: Password search: Connect with the multifunction cable the following pinout and the connections on the pcb. Use the driver: → TOOLS BOOT MODE → INFINEON TRICORE Password → PASSWORD SIMOS 12 BENCH BOX → Click on "Find Password" Now that the password has been found it's possible to read and write the control unit. See next step. Step 2: Read and write ECU Connect with the multifunction cable the pinout. (Attention: Now remove the bench box ) Do the connection shown below. Use the driver: → TOOLS BOOT MODE → INFINEON TRICORE Boot → SAK TC1797...

  Problem: I just installed the pcmtuner application I already have connected the equipment and the USB dongle but nothing responds in the application. Two errors: "User not activated" "USB Dongle Device Not Found" Solution: 1. Must send email and device serial number to tuner-box.com to activate it. 2. Install the dongle driver.

 Q: Anybody did successfully BMW mevd 17.2.9 in obd or bench mode using foxflash ? A: Yes, foxflash read and write on bench. Fox flash pinout to BOSCH MEVD17.2.9 [ 1797 ] — BMW [Gasoline] To read and write use the following driver: → BENCH TRICORE → BMW → TC1797 — BMW → MEVD17.2.9

  Problem: I got a problem running foxflash software , error "The DLL LIBCURL.DLL cannot be loaded" (shown image below). Any suggestion? Solution: Operating system issue. Change a clean system. Better be Win10 64bit. 1 Shutdown date and time automatically syncs 2: shutdown defender 3: shutdown antivirus system 4: run foxflash manager click active button 5 : keep manger run 6: run foxflash

  Question: Renault Espace 2010 SID305 Any pinout, Bench or OBD? PCMtuner site does not show pinout, window is white. Is possible read and write Sid305 in Bench? Answer: SID305 is done via OBD (module 25), so no pinout. Module 25 Renault/Nissan 1.5dCi is OBD. PCMTuner SID305 Success reports: 1). Nissan juke 1.5dci Sid305 Dtc off 2). Nissan Qashqai 1.5DCI SID305/306 OBD Read and Write — OK 3). Renault scenic3 1.5dci Read and write with pcm tuner , sid305 Dpf off 4). Renault Scenic 1.5DCI 2009 — SID305 OBD Read/Write — No problem 5). read and write via obd Renault scenic3 sid305 with no problems 6). SID305 1.5Dci OBD R/W sounds good 7). Renault Scenic 3, sid305 1,5 MB read/write OBD 8) Sid305 Obd read and write, nissan Qashqai 1.5dci 9) Renault scenic 1,5dci 2012 95cv SID305 Module 25 reading/writing stage 1 → OBD Checksum ok http://www.pcmtuner.org/pcmtuner-read-and-write-renault-scenic-sid305-by-obd/

  Foxflash programmer can read and write Ford/Fiat/Peugeot/Citroen DCU102 Visteon ecu in boot mode. You must copy flash in ST10 boot mode and eeprom. Kit to use: – Multifunction cable – 2 resistance of 1000 Ω Connect multifunction cable and the resistances as shown To read and write use the following driver: → TOOLS BOOT MODE → ST ST10Fxxx → ST10F273 / ST10F275 / ST10F276 *K or → ST10F273 / ST10F275 / ST10F276 *CAN Alternatively, read via RX TX: Kit to use: – — Multifunction cable – — 2 resistance of 1000 Ω  — Transistor PNP 2N3906 Connect multifunction cable and the resitances as shown. To read and write use the following driver: → TOOLS BOOT MODE → ST ST10Fxxx → ST10F273 / ST10F275 / ST10F276 *RxTx www.iecutool.com