Posts

FoxFlash Pinout to Fiat Marelli IAW 7GF

Image
 Can I read Fiat MARELLI IAW 7GF ECU with foxflash ecu tool ? Yes, foxflash will read and wite IAW 7GF via jtag. FoxFlash Pinout to Fiat Marelli IAW 7GF MPC5554 Connect the multifunction cable as follows: Solder the rainbow flat cable on the pcb: To read and write use the following driver: -BDM/Jtag -BDM/Jtag Mode -Jtag NEXUS MPC/SPC -MPC 55XX ECU tool recommendation: PCMtuner https://www.iecutool.com/wholesale/pcmtuner-ecu-programmer-tool.html

PCMTuner Read and Write PSA SID807EVO via Module 53

Image
  Pcmtuner new test feedback: Peugeot Patner 2015 1.6 hdi Sid807evo read and write bsl module 53, dpf egr off Ok. Check: Pinout for PSA SID807EVO Pcmtuner module 53 BSL instruction Psa Sid807EVO read, checksum and write OK Image attached: ECU tool recommendation: PCMtuner https://www.iecutool.com/wholesale/pcmtuner-ecu-programmer-tool.html

Foxflash Failed to Clone Land rover MEDC17.9 ECU?

Image
  Problem: I have tried to clone MEDC17.9 ecu and foxflash won't let me write micro flash because otp protected. Foxflash said that medc17 cloning free service. Any advice please? Cloning tool in Foxflash is for VAG Group ECU's. Check: Foxflash Tricore Clone MEDC17 ECUs Procedure ECU tool recommendation: PCMtuner https://www.iecutool.com/wholesale/pcmtuner-ecu-programmer-tool.html

Foxflash Read Mercedes Benz CRD3.20 on Bench

Image
 Foxflash read and write Mercedes Benz Sprinter CRD3.20 on bench successfully. Foxflash pinout to CRD3.20 TC1797 To read and write use the following driver: → BENCH MODE → MERCEDES BENZ → TC1797 — MERCEDES and choose: → CRD3.2x ECU tool recommendation: PCMtuner https://www.iecutool.com/wholesale/pcmtuner-ecu-programmer-tool.html

Foxflash Read and Write BMW S7 G12 MD1CP002

Image
 Foxflash programmer read and write BMW S7 G12 3.0 MD1CP002 ECU successfully. foxflash pinout to BOSCH MD1CP002 [ SPC5777] — BMW [Diesel] To read and write use the following driver: → BENCH MODE → BMW → SPC5777 — BMW → MD1CP002 ECU tool recommendation: PCMtuner https://www.iecutool.com/wholesale/pcmtuner-ecu-programmer-tool.html

Fetrotech PSA MD1CS003 Car Not Start?

Image
  Problem: Today i read and wrote md1cs003 adblue off using fetrotech tool . cheksum with fetrotech Car started 3 times and then it wouldn't start And dtc ecu P3028 What To do? Solution: TPROT off needed for PSA MD1CS003. Make Tprot off. How to do tprot on this ECU? At the address: 0x2A5D40 2D 0F 00 00 0C C2 → TPROT ON 2D 0F 00 00 82 4F → TPROT OFF if it doesn't work, rewrite original eeprom/flash for the car to start. Read also: http://www.pcmtuner.org/fetrotech-read-and-write-psa-md1cs003/ FoxFlash Read and Write PSA MD1CS003 with Tprot

Foxflash Failed to Read Suzuki Denso 64F7055 ECU?

Image
  Problem: I have a problem reading Denso suzuki swift 1.3 Denso 64F7055 full system. I use pinout by foxflash . Do i do somethingh wrong? Here is the clue. Disconnect from ecu, USB and POWER. Resrart computer if you made many attempts. Switch off MFC, try 13.5v. Reconnect and ensure all connects to ecu are firmly on, switch on MFC and restart software and try ID if 1.3 engine please make GND here, as diagram in foxflash is for 2.0/2.3 ecu FYI: Foxflash pinout to Denso 64F7055 ECU (2.0/2.3 ecu) If try all above, and still no luck reading this ecu, check ECU label. If the ecu is encrypted, foxflash cannot read it.