Alientech KESS3 update: supports Mercedes CPC ECUs and heavy-duty

 New upgrade-pack for Alientech KESS3 programmer: Reprogram heavy-duty vehicles and Mercedes Benz with "CPC" ECUs.

With the latest KESS3 upgrade, you can now expand your workshop’s capabilities by reprogramming Mercedes-Benz "CPC" ECUs, alongside newly supported ACM and UDM control units dedicated to heavy-duty vehicles.

Here’s what the new development unlocks:
With the Bosch VC1CC001 CPC5 units now supported, you can unlock unparalleled potential in Mercedes-Benz trucks. This update also enables work in "BOOT" mode on Delphi CPC2 series control units, covering a wide range of Smart and Mercedes-Benz models. This update is also a game-changer for the heavy-duty sector: support for Bosch EGC4.0 ECUs in Scania CNG trucks, Delphi DCM6.24, and Denso 275700–1762 ECUs for popular Asian brands. Finally, there are new capabilities for Continental ACM SPC564A70 and Bosch RBA1DGS1 control units in Volvo and Hino vehicles.

Supported control units:
KESS3 ECU:
•Bosch VC1CC001 CPC5
•Bosch EGC4.0
•Delphi DCM6.24
•Delphi CPC2.6.1
•Delphi CPC2.10
•Delphi CPC2.7
•Delphi CPC2.4
•Delphi CPC2.3
•Delphi CPC2.20
•Denso 275700–1762

KESS3 ACM
•Continental ACM SPC564A70

KESS3 UDM
•Bosch RBA1DGS1
Improve vehicle performance, enhance fuel efficiency, and meet all customer needs with precision and speed using a single tool that meets the high demands of today’s market.


Alientech KESS3 Update Mercedes Delphi CPC ECUs


Comments

Post a Comment

Popular posts from this blog

PCMTuner Unlock Audi SIMOS 8.6 in BSL Mode

Image
 SIMOS 8.6 requires unlocking in BSL mode by the appropriate module. BSL is usually boot mode for unlock. Same as PCR2.1 . Example: Audi A7 2012 2.8 fsi simos 8.6 unlock, after read/write simos8.6 with pcmtuner successfully. all resistor 1 kom How to work with blocks that require unlocking (PCR2.1, SIMOS8.6): 1) Check the current lock status in the car, if the check is disabled, you can go to read-write, otherwise follow the instructions 2) Remove the unit from the car, open it, transfer the processor to BSL mode using the connection below (PCR2.1, SIMOS8.6), the work as a whole as in the package 53 (you can use tools like powerbox, and you can do without them) SIMOS8.6 Unlock pcmtuner pinout Red — +12, Black — GND, Yellow — CAN-HIGH, Blue — CAN-LOW 3) Choose "SIMOS8.6 (EEPROM/UNLOCK/BSL) or PCR2.1 (EEPROM/UNLOCK/BSL)" depending of ECU type 4) Click Identification — save ECU data somewhere in a text file. 5) Click Read — save the EEPROM 6) Given that EC...
Read more

How to Find Bosch ECU Serial Numbers and Correct Pinouts

Image
 Here is basic post for people asking basic questions, apparently now on high demand since we have gathered again new members in our ECU group . So you got bosch ecu in hand from car and how to figure out how to identify it and what pinout to use? On this case we can randomly take one bosch ecu that we will identify. So all bosch ecus start with serial numbers 028… 026. We just head to bosches page next https://www.bosch-repair-service.com/ Here you search by oe or bosch number, i have random bosch ecu here and it’s 0 281 014 544 and bosch page ends up with a result. We can see its edc16cp35. Now there are two ways. Either to search in foxflash bmw / edc16cp35 for pinout. Or we head to ecu pinout page and figure out pinout from there. One of the best online pinout catalogs can be found at ecu desing, So save webpage https://ecu.design/ecu-pinout/ Copy address and head out there. Type in edc16cp35, bmw uses two processors in this one mpc 562 and mpc564. Pinouts jus...
Read more

Foxflash, KESS3, Flex: Read Fiat Marelli 9DF ECU Easily

Image
 To read Fiat Magneti Marelli IAW 9DF ECU, you have 3 options: 1.Flex in boot mode You have to open the ecu or make a hole in the center of the inscription "Magneti" Marelli" and connect the starter through the hole With Flex you can have a vr file but it doesn’t can’t write in obd. 2. Use Kess3 , Foxflash , fgtech, autotuner for obd read and obd write (To read, you need 2 hours, to write 10/15 minutes) it makes a Reading in 2h23 For mj9dfhw001 fiat ducato using foxflash. HW001 obd Hw002 boot, 5 minutes of work with opening the computer, FoxFlash takes a long time to read and write. with kess3 OBD 1:30 reading, 15 min writing. with autotuner, he does it pretty fast but only in virtual reading and reading and writing via Obd 3. Use ktag, fgtech, dfox, in jtag by open ecu. FYI: Depends on hardware version. bench is the same 2.30 hours of reading and but sometimes impossible to write. HW000 is ok to write on bench. 0001 0002 impossible to write a mod. R...
Read more