Foxflash Pinout for DSG DQ200/ DQ250 via Godiag GT107+

 People still wondering what’s up since they cannot read this and that DSG (DQ200, DQ250 etc) with foxflash.

We’ve done lots of dsg with just foxflash no other tool needed. Foxflash reads them just fine, you need either old godiag gt105+gt107 OR just newer model Godiag GT107+ in case failed to read these DSG gearbox TCUs on bench.

Once again proven that more the tools, better the support.
With FoxFlash [or with any programmer ] we can recommend getting GODIAG GT100 Diagtable (+gpt boot addon) + GT107+ (or gt105+gt107) to provide best ways on connecting to different ecu/tcu.

Also usable on kess v2 and pcmflash for dsgs and so on.

Where to get bench pinout for Foxflah+ Godiag GT107+?
Pinout to DQ200 0AM/0CW gearbox


Foxflash DSG DQ200 DQ250 etc Pinout to Godiag GT107+
Foxflash DSG DQ200 DQ250 etc Pinout to Godiag GT107+
Foxflash DSG DQ200 DQ250 etc Pinout to Godiag GT107+

Pinout to DQ250 02E/0D9 gearbox


Foxflash DSG DQ200 DQ250 etc Pinout to Godiag GT107+
Foxflash DSG DQ200 DQ250 etc Pinout to Godiag GT107+

We got some other ECU/TCU bench and GPT pinouts for Godiag GPT/GT107 adapters, contact www.iecutool.eu customer service if interested.

Comments

Post a Comment

Popular posts from this blog

FoxFlash Read and Write Volvo Denso MB279700-9xxx

Image
 Foxflash Volvo Denso MB279700–9xxx works perfectly, just follow the steps of foxflash , reading, unlocking, and writing all done on the bench. PROCEDURE: 1 — Read the Ecu AND unlock the Ecu 2 — Write the ECU READING AND UNLOCKING: Connect the following pinout using the multifunction cable. Start the driver: CAR > VOLVO > TOOLS VOLVO >UNLOCK DENSO MB279700 9641 SH72546R CAN Click on the READ FILE button to read the file. After reading, click on the UNLOCK button to unlock and enable the writing of the control unit. WRITING: Now it will be possible to reconnect the control unit to the car and write the modified file via OBD. Use the following driver: CAR > VOLVO > Model >2.0 DENSO MB279700 9641 SH72546R CAN Alternatively, you can WRITE also the ECU on the table using the pinout on the next page. Note: Compared to the read pinout, the CAN line is moved. FOXFLASH PINOUT FOR WRITING: Just follow the foxflash instructions: read file 15 min, unlock
Read more

Read/Write BMW MSV70 DME by Foxflash, Ktag or FC200?

Image
 Which tool to read this computer BMW MSV70 DME? Foxflash : Yes, via BDM Jtag Connect multifunction cable as follows: Solder the dip/sip connectors on the pcb and do a link: Insert Siemens/Marelli adapter as in photo: To read and write use the following driver: → BDM/ JTAG MODE → BDM MPC → MPC55x/56x Ktag / Kess V2 : Need luck. The best option is BDM. Sometimes Kess v2 and ktag clone read ok but failed during writing, checksum error. Ori Kess done well OBD but takes long. Easy to remove and run in bdm. CG FC200: FC200 programmer does not support this computer.
Read more

PCMTuner PSA Bosch MED17.4 Pinout

Image
 I'm trying to read one Bosch MED17.4 from a Peugeot 207 1.6t; ecu pinout is correct, but pcmtuner pcmflash shows failure, I'm using module 71 tc1766 FLASH… So, any clue? Solution: There are 2 types of pinout for med17.4. Try both. see which one works. Bosch MEDV174 IROM TC1766 EGPT PSA Pinout Feedback: Solved. Mine work with type 1 and module 71 TC1766.
Read more