PCMtuner-tool

  Foxflash new feedback: Mercedes e2/3 Temic Ecu Read pin out full system (use the driver procedure and 4/5 with switch on ignition on/off) 12v bed (24v required tho) flash and e2p read

 Here is the solution to Foxflash Mercedes Benz CRD2 or DCM3.5 ECU read ok but failed to write problem. For example: Ecu Delphi CRD2.30 OM651 Mercedes Sprinter 95KW 906 Ecu read obd file is done ok Ecu write errors, Write gets to 0 percent now it's a non starter Solution: Kess v2/ kess3 for write, foxflash bricked to write. You must write in recovery option with kess the file of read foxflash. Write original file back with kess in recovery mode. You can also use flex do recovery then start then kess read/write no problem. We recommend bench on this ecu. Obd protocols i skip if possible. Feedback: Recovery by clone kess and read and write van now started. www.iecutool.com

  Foxflash new feedback: Renault midlum 280 Trw ems2.2 (truck) Read obd ok Write obd ok Checksum by foxflash. Read 8 min Write 2 steps: 1 for 17 minutes (with 2 interruptions of 120 seconds) 1 for 7.45 minutes Obd only 64kb file. src off ok.

 How to read Peugeot 208 1.2 ecu valeo v56.12 calculator with Foxflash ? Foxflash has no protocol for this ECU. It cannot read V56.12. Need Alientech KESS3 or Autotuner. KESS3 will read and write Valeo V56.12 in boot mode. Supported models:

  Foxflash reads Renault EDC17C42 ECU ok, but failed to write. It is write protected, error "OTP sector not writable"， what else can I do? Foxflash can read and write EDC17C42 fine. Not protected. Your file is bad. Bad file try to write original file and see if all is ok you have bad file. Do checksum manually.

  Foxflash new feedback: Sid307 sak tc1767 in Mercedes Benz A180 1.5TDCI @ STAGE 1 Read Password on bench. Read/Write/checksum correction in boot mode. No pass via obd, only in boot connection. MB SID307 boot pinout to foxflash Connect with the multifunction cable the following pinout and the boot shown below. Use the driver: → TOOLS BOOT MODE → INFINEON TRICORE Boot → SAK TC1767

  Foxflash new feedback: sometimes it doesn't even work on bench the Crd3 ecu's are sensitive so to save time the boot is there for security. Mercedes cla shooting break Cdi 200 Ecu Crd3E1 Boot mode ok Read/write ok Checksum by foxflash

  PCMTuner read and write Ford Escape 2017 1.5T EMS2510 ECU successfully. Module 32 obd Read 25 minutes Write 3 minutes Everything went fine. I used pcmtuner with godiag and bench supply. Related Posts

  Foxflash new feedback: VW GOLF VI SIMOS PCR2.1 OBD OK READ OK EGR OFF OK WRITE OK Checksum by foxflash. I have disconnected and connected the battery to make flash unlock. i make obd perfectly. Car starts. www.iecutool.com

  Foxflash new user feedback: Audi a4 2020 ECU Md1cp004 Read on bench 6min Write on bench 2 min Checksum by Foxflash. All ok Foxflash pinout to Audi MD1CP004 To read and write use the following driver: → BENCH MODE → AUDI / VW → SPC5777 / TC298 — VAG → MD1CP004 www.iecutool.com

 Is it possible to read & write Mitsubishi Center Fuso ECU with pcmtuner ? Yes, with module 64 (EDC17C4–6/EDC16C31) via OBD. For example: PcmTuner OBD2 read/write Mitsubishi Fuso Canter EDC16C31 2008 4.9 engine successfully. www.iecutool.com

  Foxflash read and write Mercedes Benz Sprinter EDC15C6 via OTB mode successfully. OTB adapter is a great help. Mercedes Sprinter with a round OBD plug that requires an adapter. Simple and easy with the help of OTB. Check EDC15 C6 bench pinout Select Car OBD, Mercedes Sprinter CDI E3 EDC15C6 protocol Read ok Write ok Checksum manually with Winols. www.iecutool.com