Posts

Showing posts from March, 2023

Fetrotech Read and Write PSA MD1CS003 Tprot Off

Image
  Fetrotech tool silver read and write Md1cs003 psa on bench in 5 minutes +/-. Dpf/adblue Tprot manually. Pinout is in the document. How to do tprot on this ECU? At the address: 0x2A5D40 2D 0F 00 00 0C C2 → TPROT ON 2D 0F 00 00 82 4F → TPROT OFF NOTE: Fetrotech tool silver works with pcmtuner in default. If need to works alone, modification is required as below: http://www.pcmtuner.org/possible-to-make-fetrotech-tool-silver-work-alone/

Foxflash Read and Write Open Insignia Delco E98

Image
 Opel insignia 2.0 2016 Delco E98 foxflash Read/Write OK on bench. Flash Epprom ! checksum OK — adblue off. Here is the Opel Delco E98 ECU bench pinout to fox flash Read and write ok, checksum by foxflash

Foxflash Failed to Read Audi EDC17CP44 via OBD?

Image
  Problem: I try an Audi EDC17CP44 virtual reading with foxflash today, it reads OK, but failed to write file (i bought from tuner). i get this error. Any soultion? Solution: Edc17CP44 without 100% correct VR file is impossible to write. No VR file on server matches, just read/write on bench. only manual solutions from professionals, because this ecu should have 3xOTP. Read on bench, then check if the bench file you read is original by comparing it with the file you bought, if it is not just revert the changes to your bench file with WinOLS and start from there. As the VR was not on server, you must read the ECU on bench, modify file and Write on Bench. If the VR is not on server, don't try and just write a sourced file (internet etc etc) via OBD to try to save time. Foxflash Audi EDC17CP44 bench pinout To read and write use the following driver: → BENCH TRICORE → VOLKSWAGEN/AUDI/SEAT/SKODA/PORSCHE → TC1797 — VAG → EDC17 CP44

Read EDC7C32 with PCMTuner or Foxflash?

Image
 How to read ecu man edc7c32 with pcmtuner ? EDC7 from Fuso/canter is only supported PCMtuner. For MAN EDC7C32 you will need foxflash programmer. Here is the EDC7 C32 pinout to fox flash. To read and write use the following driver: -> Bench mode ->MAN ->MPC5612-MAN ->EDC7 C32

Foxflash Read BMW ZF 8HP Gearbox via OBD

Image
 OBD reading the BMW ZF 8 HP gearbox with Foxflash ecu programmer , nbt id4 carplay bonus and sport display modification stage 2. It works ! Connect foxflash via OBD. Select menu TCU Gear BMW Gear-> 4 Series (F32-F33-F36)->ZF 8HP *CAN. Get ID OK Read data OK Modify data by tuner.

Fetrotech Black Read and Write MED9.1 MPC562

Image
  Fetrotech Black standalone read and write Med9.1 MPC562. Read very fast. I've tried on two ecu and everything is fast. read fast and pinout is good. Checksum its ok for that ecu. Wrote succeed. check bench pinout in tuner-box.com Read and write no problem.

PCMTuner Failed to Read Renault EMS3132 via OBD?

Image
  Problem: I tried to read CONTINENTAL EMS 3132 Renault with pcmtuner module 38 via OBD, but shows an identification failure. Any idea? Solution: Some succeeded reading Renault EMS 3132 with pcm tuner. But between any identification you must disconnect pcmtuner. Disconnect from OBD port and switch of ignition, restart pcmtuner flash, and plug in obd and put ignition back on. If failed to read it by OBD, you can try module 53 BSL mode. Ktag is good on Renault ems 3132 in boot mode. Foxflash will read it on bench bench pinout also boot mode. SIEMENS EMS 3132 [C167] — Renault [ Gasoline ] boot pinout

Foxflash Delphi DCM3.7AP Jtag Pinout

Image
 How to read/write a Delphi DCM3.7AP ecu with foxflash ecu programmer ? Foxflash will read Cheverolet, GM and Opel Delphi DCM3.7AP MPC55xx ecus. Delphi DCM3.7AP Jtag MPC55xx pinout to Foxflash Delphi DCM3.7AP MPC55xx Solder the rainbow flat cable on the pcb: To read and write use the following driver: ->BDM/Jtag ->BDM/Jtag Mode ->Jtag Nexus MPC/SPC ->MPC 55xx

PCMTuner Failed to Read Mercedes MED17.1.1 Solution

Image
  PCMTuner Module 69 Mercedes MED 17.1.1 1.Read DTC Complete 2.Identification Complete But I can not read like photo, (Failure , file not found try again later) Error codes 404,13,0 I did same ecu 2pcs but the same error. I check sereval times pin connector, that is all right, help me please. Solution: Mercedes module is OBD not bench, you need 71 to read med/edc17 on bench. module 71 for bench or 53 for boot. Mercedes ME17.1.1 bench pinout to pcmtuner

PCMTuner "File Integrity Violated" Error Solution

Image
  Question: I have this problem when launching pcmtuner software . I reinstall windows and have a problem installing pcm, (downloading microsoft edge webview2 and after download installer says not work for my system. Only win10). Installation stop. Solution: First error means you system has malware and viruses which have infected your files. Please install on a clean computer! try to use win10 or win7 with 64bit. Feedback: Problem solved after installing manually microsoft edge.

PCMTuner Error Problem Preparing Selected File Solution

Image
  Problem: I need to read Alfa Romeo Giulietta with EDC17C69 control unit with pcmtuner . When I read both Eeprom and microprocessor, it makes me write the Eeprom but does not write the micro. if I write the Eeprom with the same file that I have read, everything is ok. If I write the chip with the same file that I read, it gives me the message of the photo. Any idea? Solution: You are trying to write the file in the eeprom. Need to Change to flash. You need to select Flash in drop down box to write flash! you cannot write flash if eprom is selected. Select flash in the drop-down menu and flash your file, not flash in eeprom.

Will Foxflash Read Kubota EDC17CV45 ECU?

Image
  Problem: Will foxflash programmer read and write edc17cv45 or not? I don't see anywhere in software have Kubota edc17cv45, where it's ? Solution: foxflash software does not have Kubota edc17cv45 driver on the list. But there is a BOSCH EDC17 CV54 [1767 ]– Agco [Diesel] driver. If the processor CPU is the same as TC1767 there is a chance to read/write it on bench. To read and write EDC17CV45 [1767] use the following driver: → BENCH TRICORE → AGCO → TC1767 – AGCO → EDC17 CV54 Pinout is the same for KUBOTA EDC17cv45 tc1767 If CPU processor is not TC1767, then fox flash will not read and write this ecu. You may need other programmers, dimsport etc. Here is the bench pinout to Bosch EDC17CV45 TC1872 Kubota to dimsport.

Foxflash Update FCA GPEC2 GPEC3 GPEC4LM GPEC2A ECUs

Image
 Good news! Foxflash ecu programmer released new update- adding FCA group GPEC2 GPEC3 GPEC4LM GPEC2A ECUs. Continental GPEC2 GPEC3 GPEC4LM GPEC2A – foxFlash is now able to perform the Continental GPEC2 GPEC3 GPEC4LM GPEC2A foxFlash is now able to perform the following operations: Boot Read Boot Write On the following ECU reference: Continental GPEC2 GPEC3 GPEC4LM GPEC2A Chrysler 200 Continental GPEC3 BOOT Chrysler 200 Continental GPEC3 BOOT Chrysler 300 mk2 Continental GPEC2A BOOT Chrysler 300 mk2 Continental GPEC2A BOOT Chrysler Aspen Continental GPEC2A BOOT Chrysler Grand VojagerContinental GPEC2A BOOT Chrysler Town & CountryContinental GPEC2A BOOT Dodge Avenger Continental GPEC2A BOOT Dodge Avenger Continental GPEC2A BOOT Dodge ChallengerContinental GPEC2A BOOT Dodge ChallengerContinental GPEC2A BOOT Dodge Charger Continental GPEC2A BOOT Dodge Charger Continental GPEC2A BOOT Dodge Dart Continental GPEC3 BOOT Dodge Durango Continental GPEC2A BOOT ...

Foxflash Read and Write MEDC17.9 OTP via OBD on Bench

Image
 OBD on the bench reading the MEDC17.9 with foxflash programmer + godiag gt100 breakout box. I want to try and write the modified files via OBD after an OBD read. The ECU data that had been corrupted is now all OK. Updated: I have had an interesting case with this ECU MEDC17.9 that had failed and had the OTP block. I read the Full flash via OBD, had the flash modified to delete CAT/AdBlue/DPF and EGR (use a tuning file service). When I got the modified file back, I decided to write it via Bench mode. I did the checksum correction using the original flash and flashed it via Bench mode 100% without any problems. The car is now starting and has no faults whatsoever and drives very well. We had brought it on a flatbed. Another great success with FoxFlash and a bit of experimenting. Read via obd on bench Write on bench MEDC17.9 bench pinout to fox flash To read and write use the following driver: → BENCH TRICORE → JAGUAR → TC1793 — JAGUAR → MEDC17.9 Attention: Some ...