PCMtuner-tool

  OBDSTAR DC706 new user feedback: It is a VW Bosch ME7.5 ECU, Part number 0261207619. it doesn’t give access. Entering through ME7.5.10 kline menu even though the ecu is 80 pins still does everything ok. Function: Read EXT eeprom 95040 Read EXT flash 29F400BT Write EXT eeprom 95040 Write EXT flash 29F400BT Read pin code IMMO ON/IMMO OFF Write VIN.

  How-to guide: install, activate   PADFlash ECU TCU Programmer software , check wiring diagram and use software. Operating system requirements:  Win7 64bit (Win10 64bit coming soon) Computer hardware requirements:  RAM not less than 4GB, CPU not less than 2.5GHz How to Install & Active PADFlash Software on Win10? Currently, there is no software download link available. The software can only be installed remotely. The technician will upload the software later, and we will then update the instructions for self-installation. After receiving the device, please follow the steps below to install it 1: Please install Teamviwer remote control software on your computer 2: Connect the device host USB cable to the computer 3: Insert the USB KEY that comes with the device into the computer 4: Maintain a good working network 5: Turn on your teamviewer device and send the remote control ID and password to your sales, or send an email to  info@padflashr.uk 6: Remote techn...

  Problem: Failed to install foxflash software 1.4.3. It reported an error "The code execution cannot proceed because VCRUNTIME140.dll was not found." Struggling to get past this point. Solution: Install vc redistributable x64. It should be fine.

 Peugeot boxer DCM6.2F DPF-AdBlue removal and stage 1. The DCM6.2F is a Delphi ECU that is used in some Peugeot Boxer 2.0 BlueHDI vans. HDI Tuning offers a software remap for the DCM6.2C ECU in these vans. Read and write with foxflash programmer via OBD. All went good, the map made a big difference, no smoke and the van is pulling way better even the customer thinks it’s too fast. On vag cars 6.2 is vr file! If VR in system should be good, always use power supply on obd.

  Problem: Foxflash failed to read VW Simos 18.1 tc1792 ecu in boot mode. I have 14.5V And checked Pinout 2 times. There’s always this error (no response with ECU) and wake error. Any solution? Solution: 1). Voltage issue. Set to 13v. Too much voltage at the moment if 14.5v. Some ecus need very specific voltage, start allways from 12v and try again by raising voltage in steps of +0.5v. So 12v read, 12.5v read ,13v read and so on.. up to 14v. Rare cases need to go above 14v. 2). Pinout issue. You need to change the arrangement of the resistors. Because at this point on one pin where you are supposed to have 1k ohm you have 2k ohm. www.iecutool.eu

 Will Padflash programmer read and write Ford Siemens VDO SID902 ECU? Yes, PADFlash will read and write SID902 via Jtag . SID902 is not possible to do on bench mode. Only Jtag or OBD. PADFlash can do it via Jtag mode. PAD Flash software will show you jtag wiring diagram. If need to read SID902 ECU via OBD , choose Alientech KESS3 , Flex or Autotuner.

 Here is the tip to read Benz MED17.7.3 ECU with Foxflash programmer . MED17.7.3 Read/write/checksum ok. Mistake in pinout in foxflash manual use pinout for med17.7.3.1 which use +12 in the left corner not that middle left like in wiring. To read and write use the following driver: → BENCH TRICORE → MERCEDES → TC1797 — MERCEDES → MED17.7.3