PCMtuner-tool

  Problem: I have a problem with my id on vag simos pcr 2.1 with foxflash software on bench. 12.3v battery and connections ok it doesn't make me ID, what could it be? Solution: Check PIN out if ok the problem is the voltage. For pcr2.1 needs minimum 13v. V13.5 is recommended. Change power supply and try again. Feedback: In fact, the voltage has risen and it went well. Read also: http://www.pcmtuner.org/foxflash-unlock-vw-polo-2013-pcr2-1-on-bench/ www.iecutool.com

 Man TGX 18.440 EDC7C32. Reading works with foxflash by OBD. Does the writing via obd of this ecu work? Yes, Read and write ok via obd. If you do not risk writing a heavy vehicle by OBD, do it on bench. Backup with bench. Then do OBD. Same MPC in bench. Bench is easy and faster. No problems at all. Foxflash pinout to MAN truck edc7c32 ecu To read and write use the following driver: → BENCH MODE → MAN → MPC561/2 — MAN → EDC7 C32 www.iecutool.com

  Problem: My foxflash tool cannot read and write BMW MEV946 protocol by OBD, any advice? Solution: Make sure you have done driver seatbeal on, hazzard lights on and driver door open so dash not got in sleep mode. If still failed to read/write via OBD, there is no VR file on server. Also try to read ecu via OBD on bench using godiag breakout box . Or use kess v2 . Kess make it via OBD without problem.

 PCMTuner can be used as a good j2534 passthru device for multiple software. iECUTool engineer just tested latest version GDS2 2023.7 software with pcmtuner and confirmed it works great. Preparation: GM GDS2 2023.7.13 download PCMTuner driver download How to Install GM GDS2 2023.7.13 for PCMTuner ? Download GDS2 software, install GDS2AutoInstall Delete GDS2 shortcut on desktop Go to C://Program Files(x86)/GDS2/bin folder, send GDS2Launcher to desktop Rename GDS2launcher shorcut as GDS2 Contact www.iecutool.com customer service to activate GDS2 via Teamviewer. Then install pcmtuner driver Go to computer Device Manager, make sure pcmtuner is well connected and driver is detected. Run GDS2 on desktop Select interface as SM2 USB Now software is ready to use. www.iecutool.com

 Here comes a similar problem: Im reading in Jtag Mode Isuzu Dmax Transtron ECU with foxflash , I can connect to ecu with jtag connection and it's reading, but at the end I get this error and file is not ok, it's empty. Error "File not recognized, send file to technical support Checksum will not be calculated"!!! What's the Problem? Solution: The file on ecu is not recognized by foxflash tool, so it cannot perform the necessary checksum calculations, it is warning not error. This could be due to reading error, jtag do not need such high voltage, try 12.5v.

  Problem: My foxflash software has flown, "Select driver" has turned gray and the battery voltage is no longer showing up. Do you have a solution? I reinstalled it already but no difference. Solution: 1. Run FoxFlash Manager, press "Activated", Keep Fox flash manager running. DO NOT CLOSE MANAGER!!! 2. Run Foxflash software NOTE: Make sure internet is connected! Tool must be connected and powered via 12v. If not working, try with another USB port. You can bench power supply or OBD cable, but tool doesn't work without power.

 Q: Is it possible to somehow read psa sid807evo with Foxflash? A: Yes, via boot mode. SIEMENS CONTINENTAL 807EVO [T1797 INT.F] — PSA Pinout to Foxflash 1. Read and Write ECU Connect with the multifunction cable the following pinout and the boot shown below Use the driver: → TOOLS BOOT MODE → INFINEON TRICORE Boot → SAK TC1797 Note: Some hardware versions boot in the manner shown on the next image. Example of connection: Attention: On some ECUs and for tools with version firmware < 70 it is only possible to use this type of boot: www.iecutool.com Read also: PCMTuner Read and Write PSA SID807EVO via Module 53 BSL