PCMtuner-tool

 New Foxflash slave version will be available by the end of October 2023. What's the Difference Between Foxflash Master and Slave? The difference between the Slave and Master is the ability to access and edit the data read from the vehicle. With a slave tool you read and write encrypted files. These files can only be modified by a specific master. This master is a file provider designated when you buy the tool. Your slave tool is linked to this master. Does the slave version have all of the foxFlash function? Yes, it have all of the foxFlash function. Who need Slave tool? 1: Anyone who cant develop his own tuning file, but need some good tuner can supply, so they will need it . 2: Anyone who wants a lower price get this tool. 3: Anyone master owner want to develop his own dealer tuning net in the world. Can this foxflash slave tool upgrade to Master? Yes, you can upgrade it as master, Any slave tool can be remotely transformed into master tool if the follow...

  Foxflash read and write Renault Continental EMS3155 perfectly in boot mode, checksum by tool. Read and write work good. SIEMENS EMS3155 [ TC1782 INT.F.] — Renault Foxflash Pinout 1.Search password: To find the password, connect via OBD to the car. Use the driver: → TOOLS BOOT MODE → INFINEON TRICORE Tool Password → OBD PASSWORD EMS3155 RENAULT — NISSAN → Click on "Find Password" and follow the software messages The password can also be found on the desk by connecting the following pinout. Now that the password has been found it's possible to read and write the control unit. See next step. 2. Read and write ECU Connect with the multifunction cable the following pinout and the boot shown below. Use the driver: → TOOLS BOOT MODE → INFINEON TRICORE Boot → SAK TC1782 www.iecutool.com

  Problem: I have a problem with my id on vag simos pcr 2.1 with foxflash software on bench. 12.3v battery and connections ok it doesn't make me ID, what could it be? Solution: Check PIN out if ok the problem is the voltage. For pcr2.1 needs minimum 13v. V13.5 is recommended. Change power supply and try again. Feedback: In fact, the voltage has risen and it went well. Read also: http://www.pcmtuner.org/foxflash-unlock-vw-polo-2013-pcr2-1-on-bench/ www.iecutool.com

 Man TGX 18.440 EDC7C32. Reading works with foxflash by OBD. Does the writing via obd of this ecu work? Yes, Read and write ok via obd. If you do not risk writing a heavy vehicle by OBD, do it on bench. Backup with bench. Then do OBD. Same MPC in bench. Bench is easy and faster. No problems at all. Foxflash pinout to MAN truck edc7c32 ecu To read and write use the following driver: → BENCH MODE → MAN → MPC561/2 — MAN → EDC7 C32 www.iecutool.com

  Problem: My foxflash tool cannot read and write BMW MEV946 protocol by OBD, any advice? Solution: Make sure you have done driver seatbeal on, hazzard lights on and driver door open so dash not got in sleep mode. If still failed to read/write via OBD, there is no VR file on server. Also try to read ecu via OBD on bench using godiag breakout box . Or use kess v2 . Kess make it via OBD without problem.

 PCMTuner can be used as a good j2534 passthru device for multiple software. iECUTool engineer just tested latest version GDS2 2023.7 software with pcmtuner and confirmed it works great. Preparation: GM GDS2 2023.7.13 download PCMTuner driver download How to Install GM GDS2 2023.7.13 for PCMTuner ? Download GDS2 software, install GDS2AutoInstall Delete GDS2 shortcut on desktop Go to C://Program Files(x86)/GDS2/bin folder, send GDS2Launcher to desktop Rename GDS2launcher shorcut as GDS2 Contact www.iecutool.com customer service to activate GDS2 via Teamviewer. Then install pcmtuner driver Go to computer Device Manager, make sure pcmtuner is well connected and driver is detected. Run GDS2 on desktop Select interface as SM2 USB Now software is ready to use. www.iecutool.com

 Here comes a similar problem: Im reading in Jtag Mode Isuzu Dmax Transtron ECU with foxflash , I can connect to ecu with jtag connection and it's reading, but at the end I get this error and file is not ok, it's empty. Error "File not recognized, send file to technical support Checksum will not be calculated"!!! What's the Problem? Solution: The file on ecu is not recognized by foxflash tool, so it cannot perform the necessary checksum calculations, it is warning not error. This could be due to reading error, jtag do not need such high voltage, try 12.5v.

  Problem: My foxflash software has flown, "Select driver" has turned gray and the battery voltage is no longer showing up. Do you have a solution? I reinstalled it already but no difference. Solution: 1. Run FoxFlash Manager, press "Activated", Keep Fox flash manager running. DO NOT CLOSE MANAGER!!! 2. Run Foxflash software NOTE: Make sure internet is connected! Tool must be connected and powered via 12v. If not working, try with another USB port. You can bench power supply or OBD cable, but tool doesn't work without power.

 Q: Is it possible to somehow read psa sid807evo with Foxflash? A: Yes, via boot mode. SIEMENS CONTINENTAL 807EVO [T1797 INT.F] — PSA Pinout to Foxflash 1. Read and Write ECU Connect with the multifunction cable the following pinout and the boot shown below Use the driver: → TOOLS BOOT MODE → INFINEON TRICORE Boot → SAK TC1797 Note: Some hardware versions boot in the manner shown on the next image. Example of connection: Attention: On some ECUs and for tools with version firmware < 70 it is only possible to use this type of boot: www.iecutool.com Read also: PCMTuner Read and Write PSA SID807EVO via Module 53 BSL

  Problem: After write in ecu with foxflash tool ecu is bricked, ecu is EDC17CV42 Man Tgs 2014. Have full beckup and no work write File with backup, problem password. Ecu work read File and No work write. Any advice? Solution: You need to find password. Search password in flash file (tool boot password) and then you can write. Try to search in obd file but normally it will do in bench, but you can try with obd file. Since time better to make backup in bench before try to obd. Once you already extracted the password, read write normally.

 Can Foxflash read and write Ford Ranger SID209? Yes, first read obd password after that remove ecu and read/write boot mode. Reading was 2 mins, writing is 15–17 mins. SIEMENS CONTINENTAL SID209 [ TC1797 INT.F.] — Ford Boot Pinout to Foxflash Step 1: Password Search Connect the pinout and use the following driver: Use the driver: → TOOLS BOOT MODE → INFINEON TRICORE Tool Password → OBD PASSWORD SID209 FORD → Click on "Find Password" and follow the software messages. Attention: If you cannot find the password from Pinuot, you must launch the driver in OBD on the vehicle. Now that the password has been found it's possible to read and write the control unit. See next step. Step 2: Read and Write ECU Connect with the multifunction cable the following pinout and the boot shown below Use the foxflash driver : → TOOLS BOOT MODE → INFINEON TRICORE Boot → SAK TC1797 www.iecutool.com

  Problem: Usage problem, the pc (Win11 system) has a lot of RAM and an empty hard drive and yet I have this error when reading EDC16C34 with foxflash . Error "Your computer's memory is insufficient" Solution: The error usually caused by insufficient computer memory. If your computer has enough RAM, try to delete foxflash software and install again. Feedback: Problem solved, remove foxflash then reinstall software. It works now.

 Godiag GT107+ is the upgrade version of GT107 . You don't need to connect extra GT105 breakout box to read gearbox TCUs. Here is an example of reading VAG DQ200 gearbox using gt107+. Device used: Pcmtuner programmer or kess v2 (pcmtuner is faster than kess v2 to read DSG gearbox) Godiag GT107+ DSG gearbox adapter Procedure: Connect pcmtuner with USB and main cable Connect pcmtuner with gt107+ gearbox adapter Connect jumper cable with DQ200 gearbox module follow the pinout Turn on ignition on the gt107+ Run pcmtuner flash software Select module 58 and read DQ200 data. It writes without problem as well. www.iecutool.com Read also: http://www.pcmtuner.org/pcmtuner-module-58-vag-dsg-cvt-instruction/