PCMtuner-tool

 Here comes a similar problem: Im reading in Jtag Mode Isuzu Dmax Transtron ECU with foxflash , I can connect to ecu with jtag connection and it's reading, but at the end I get this error and file is not ok, it's empty. Error "File not recognized, send file to technical support Checksum will not be calculated"!!! What's the Problem? Solution: The file on ecu is not recognized by foxflash tool, so it cannot perform the necessary checksum calculations, it is warning not error. This could be due to reading error, jtag do not need such high voltage, try 12.5v.

  Problem: My foxflash software has flown, "Select driver" has turned gray and the battery voltage is no longer showing up. Do you have a solution? I reinstalled it already but no difference. Solution: 1. Run FoxFlash Manager, press "Activated", Keep Fox flash manager running. DO NOT CLOSE MANAGER!!! 2. Run Foxflash software NOTE: Make sure internet is connected! Tool must be connected and powered via 12v. If not working, try with another USB port. You can bench power supply or OBD cable, but tool doesn't work without power.

 Q: Is it possible to somehow read psa sid807evo with Foxflash? A: Yes, via boot mode. SIEMENS CONTINENTAL 807EVO [T1797 INT.F] — PSA Pinout to Foxflash 1. Read and Write ECU Connect with the multifunction cable the following pinout and the boot shown below Use the driver: → TOOLS BOOT MODE → INFINEON TRICORE Boot → SAK TC1797 Note: Some hardware versions boot in the manner shown on the next image. Example of connection: Attention: On some ECUs and for tools with version firmware < 70 it is only possible to use this type of boot: www.iecutool.com Read also: PCMTuner Read and Write PSA SID807EVO via Module 53 BSL

  Problem: After write in ecu with foxflash tool ecu is bricked, ecu is EDC17CV42 Man Tgs 2014. Have full beckup and no work write File with backup, problem password. Ecu work read File and No work write. Any advice? Solution: You need to find password. Search password in flash file (tool boot password) and then you can write. Try to search in obd file but normally it will do in bench, but you can try with obd file. Since time better to make backup in bench before try to obd. Once you already extracted the password, read write normally.

 Can Foxflash read and write Ford Ranger SID209? Yes, first read obd password after that remove ecu and read/write boot mode. Reading was 2 mins, writing is 15–17 mins. SIEMENS CONTINENTAL SID209 [ TC1797 INT.F.] — Ford Boot Pinout to Foxflash Step 1: Password Search Connect the pinout and use the following driver: Use the driver: → TOOLS BOOT MODE → INFINEON TRICORE Tool Password → OBD PASSWORD SID209 FORD → Click on "Find Password" and follow the software messages. Attention: If you cannot find the password from Pinuot, you must launch the driver in OBD on the vehicle. Now that the password has been found it's possible to read and write the control unit. See next step. Step 2: Read and Write ECU Connect with the multifunction cable the following pinout and the boot shown below Use the foxflash driver : → TOOLS BOOT MODE → INFINEON TRICORE Boot → SAK TC1797 www.iecutool.com

  Problem: Usage problem, the pc (Win11 system) has a lot of RAM and an empty hard drive and yet I have this error when reading EDC16C34 with foxflash . Error "Your computer's memory is insufficient" Solution: The error usually caused by insufficient computer memory. If your computer has enough RAM, try to delete foxflash software and install again. Feedback: Problem solved, remove foxflash then reinstall software. It works now.

 Godiag GT107+ is the upgrade version of GT107 . You don't need to connect extra GT105 breakout box to read gearbox TCUs. Here is an example of reading VAG DQ200 gearbox using gt107+. Device used: Pcmtuner programmer or kess v2 (pcmtuner is faster than kess v2 to read DSG gearbox) Godiag GT107+ DSG gearbox adapter Procedure: Connect pcmtuner with USB and main cable Connect pcmtuner with gt107+ gearbox adapter Connect jumper cable with DQ200 gearbox module follow the pinout Turn on ignition on the gt107+ Run pcmtuner flash software Select module 58 and read DQ200 data. It writes without problem as well. www.iecutool.com Read also: http://www.pcmtuner.org/pcmtuner-module-58-vag-dsg-cvt-instruction/